AT91SAM7X128-CU Atmel, AT91SAM7X128-CU Datasheet - Page 511

• Manufacturer Part Number: AT91SAM7X128-CU
• Description: MCU ARM 128K HS FLASH 100-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X128-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7X-EK - KIT EVAL FOR AT91SAM7X256/128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

36.6.3
6120H–ATARM–17-Feb-09
Time Management Unit
The CAN Controller integrates a free-running 16-bit internal timer. The counter is driven by the
bit clock of the CAN bus line. It is enabled when the CAN controller is enabled (CANEN set in the
CAN_MR register). It is automatically cleared in the following cases:
The application can also reset the internal timer by setting TIMRST in the CAN_TCR register.
The current value of the internal timer is always accessible by reading the CAN_TIM register.
When the timer rolls-over from FFFFh to 0000h, TOVF (Timer Overflow) signal in the CAN_SR
register is set. TOVF bit in the CAN_SR register is cleared by reading the CAN_SR register.
Depending on the corresponding interrupt mask in the CAN_IMR register, an interrupt is gener-
ated while TOVF is set.
In a CAN network, some CAN devices may have a larger counter. In this case, the application
can also decide to freeze the internal counter when the timer reaches FFFFh and to wait for a
restart condition from another device. This feature is enabled by setting TIMFRZ in the CAN_MR
register. The CAN_TIM register is frozen to the FFFFh value. A clear condition described above
restarts the timer. A timer overflow (TOVF) interrupt is triggered.
To monitor the CAN bus activity, the CAN_TIM register is copied to the CAN _TIMESTP register
after each start of frame or end of frame and a TSTP interrupt is triggered. If TEOF bit in the
CAN_MR register is set, the value is captured at each End Of Frame, else it is captured at each
Start Of Frame. Depending on the corresponding mask in the CAN_IMR register, an interrupt is
generated while TSTP is set in the CAN_SR. TSTP bit is cleared by reading the CAN_SR
register.
The time management unit can operate in one of the two following modes:
Timestamping Mode is enabled by clearing TTM field in the CAN_MR register. Time Triggered
Mode is enabled by setting TTM field in the CAN_MR register.
• after a reset
• when the CAN controller is in Low-power Mode is enabled (LPM bit set in the CAN_MR and
• after a reset of the CAN controller (CANEN bit in the CAN_MR register)
• in Time-triggered Mode, when a message is accepted by the last mailbox (rising edge of the
• Timestamping mode: The value of the internal timer is captured at each Start Of Frame or
• Time Triggered mode: A mailbox transfer operation is triggered when the internal timer
SLEEP bit set in the CAN_SR)
MRDY signal in the CAN_MSR
each End Of Frame
reaches the mailbox trigger.
AT91SAM7X512/256/128 Preliminary
last_mailbox_number
register).
511