AT91SAM7X128-CU Atmel, AT91SAM7X128-CU Datasheet - Page 512

• Manufacturer Part Number: AT91SAM7X128-CU
• Description: MCU ARM 128K HS FLASH 100-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X128-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7X-EK - KIT EVAL FOR AT91SAM7X256/128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

36.6.4
36.6.4.1
6120H–ATARM–17-Feb-09
CAN 2.0 Standard Features
CAN Bit Timing Configuration
All controllers on a CAN bus must have the same bit rate and bit length. At different clock fre-
quencies of the individual controllers, the bit rate has to be adjusted by the time segments.
The CAN protocol specification partitions the nominal bit time into four different segments:
Figure 36-4. Partition of the CAN Bit Time
The TIME QUANTUM (TQ) is a fixed unit of time derived from the MCK period. The total number
of TIME QUANTA in a bit time is programmable from 8 to 25.
SYNC SEG: SYNChronization Segment.
This part of the bit time is used to synchronize the various nodes on the bus. An edge is
expected to lie within this segment. It is 1 TQ long.
This part of the bit time is used to compensate for the physical delay times within the network. It
is twice the sum of the signal’s propagation time on the bus line, the input comparator delay, and
the output driver delay. It is programmable to be 1,2,..., 8 TQ long.
This parameter is defined in the PROPAG field of the
The Phase-Buffer-Segments are used to compensate for edge phase errors. These segments
can be lengthened (PHASE SEG1) or shortened (PHASE SEG2) by resynchronization.
Phase Segment 1 is programmable to be 1,2,..., 8 TQ long.
Phase Segment 2 length has to be at least as long as the Information Processing Time (IPT)
and may not be more than the length of Phase Segment 1.
These parameters are defined in the PHASE1 and PHASE2 fields of the
Register”.
The Information Processing Time (IPT) is the time required for the logic to determine the bit level
of a sampled bit. The IPT begins at the sample point, is measured in TQ and is fixed at 2 TQ for
the Atmel CAN. Since Phase Segment 2 also begins at the sample point and is the last seg-
ment in the bit time, PHASE SEG2 shall not be less than the IPT.
• TIME QUANTUM
• PROP SEG: PROPagation Segment.
• PHASE SEG1, PHASE SEG2: PHASE Segment 1 and 2.
• INFORMATION PROCESSING TIME:
• SAMPLE POINT:
SYNC_SEG
AT91SAM7X512/256/128 Preliminary
PROP_SEG
NOMINAL BIT TIME
PHASE_SEG1
”CAN Baudrate
Sample Point
PHASE_SEG2
Register”.
”CAN Baudrate
512