MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 107

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 11
Input/Output Ports (PORTS)
11.1 Introduction
The MC68HC908QC16 has up to 24 bidirectional input-output (I/O) pins and two input only pins
depending on the package selection. All I/O pins are programmable as inputs and outputs.
11.2 Unused Pin Termination
Input pins and I/O port pins that are not used in the application must be terminated. This prevents excess
current caused by floating inputs, and enhances immunity during noise or transient events. Termination
methods include:
Never connect unused pins directly to V
Since some general-purpose I/O pins are not available on all packages, these pins must be terminated
as well. Either method 1 or 2 above are appropriate.
11.3 Port A
Port A is an 6-bit special function port that shares all six of its pins with the keyboard interrupt (KBI)
module (see
configurable pullup device if the corresponding port pin is configured as an input port.
Freescale Semiconductor
1. Configuring unused pins as outputs and driving high or low;
2. Configuring unused pins as inputs and enabling internal pull-ups;
3. Configuring unused pins as inputs and using external pull-up or pull-down resistors.
Chapter 8 Keyboard Interrupt Module
PTA2 is input only. PTA2 has a high voltage detector to enable entry into
special modes. Do not exceed the V
When the IRQ function is enabled in the configuration register 2
(CONFIG2), bit 2 of the port A data register (PTA) will always read a 0. In
this case, the BIH and BIL instructions can be used to read the logic level
on the PTA2 pin. When the IRQ function is disabled, these instructions will
behave as if the PTA2 pin is a logic 1. However, reading bit 2 of PTA will
read the actual logic level on the pin.
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
DD
or V
SS
NOTE
.
DD
(KBI)). Each port A pin also has a software
level on this pin in normal operation.
107