MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 117

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 12
Periodic Wakeup Module (PWU)
12.1 Introduction
This section describes the periodic wakeup (PWU) module.The PWU is available in all modes of
operation (run, wait, and stop) and performs two main functions:
12.2 Features
Features of the periodic wakeup module include:
12.3 Functional Description
Figure 12-1
The PWU module consists of a PWU counter whose count is reset once it equals the value stored in the
PWU modulo register (PWUMOD). The PWU counter clock, PWUCLOCK, frequency is selectable using
the PWU prescaler register (PWUP). The prescaler clock source can be selected using the PWUCLKSEL
bit in the PWU status and control register (PWUSC) and can either be the internal RC oscillator or the
BUSCLKX4 clock.The PWUCLKSEL bit, PWUMOD and PWUP registers can only be written to when the
PWUON bit is clear.
The PWUON bit in PWUSC is used to enable the PWU module. The SMODE bit in PWUSC is used to
allow an enabled PWU module to continue running in stop mode. BUSCLKX4 must be enabled to run in
stop mode if used as the clock source for the PWU when SMODE is set. See
Registers (CONFIG1 and CONFIG2)
The PWU counter when enabled will count until it reaches the value stored in the PWU modulo register
(PWUMOD), when they are equal the read-only PWU flag (PWUF) in PWUSC is latched. The PWU
interrupt enable bit, PWUIE, in PWUSC enables a PWU interrupt request. The PWUF can be cleared by
writing to the PWU acknowledge bit, PWUACK in PWUSC or by a PWU interrupt vector fetch.
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
Generate periodic wakeup requests to bring the microcontroller unit (MCU) out of stop mode.
Generate periodic interrupt requests during run and wait modes.
Interrupt with separate interrupt enable bit, interrupt vector and interrupt mask bit
Exit from low-power stop mode without external signals
Programmable clock input
Selectable timeout periods (40
periods over 4 ms)
Dedicated low-power 32 kHz internal oscillator separate from the main system clock sources
Option to allow bus clock source to run the PWU
Accessible in all modes of operation (run, wait, and stop)
is a block diagram of the PWU.
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
µ
on enabling BUSCLKX4 to run in stop mode.
s to 3 minutes with an adjustment resolution of better than 1% for
Chapter 4 Configuration
117