MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 54

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Analog-to-Digital Converter (ADC10) Module
3.7.5 ADC10 Channel Pins (ADn)
The ADC10 has multiple input channels. Empirical data shows that capacitors on the analog inputs
improve performance in the presence of noise or when the source impedance is high. 0.01 µF capacitors
with good high-frequency characteristics are sufficient. These capacitors are not necessary in all cases,
but when used they must be placed as close as possible to the package pins and be referenced to V
3.8 Registers
These registers control and monitor operation of the ADC10:
3.8.1 ADC10 Status and Control Register
This section describes the function of the ADC10 status and control register (ADSCR). Writing ADSCR
aborts the current conversion and initiates a new conversion (if the ADCH[4:0] bits are equal to a value
other than all 1s).
COCO — Conversion Complete Bit
AIEN — ADC10 Interrupt Enable Bit
ADCO — ADC10 Continuous Conversion Bit
54
•
•
•
COCO is a read-only bit which is set each time a conversion is completed. This bit is cleared whenever
the status and control register is written or whenever the data register (low) is read.
When this bit is set, an interrupt is generated at the end of a conversion. The interrupt signal is cleared
when the data register is read or the status/control register is written.
When this bit is set, the ADC10 will begin to convert samples continuously (continuous conversion
mode) and update the result registers at the end of each conversion, provided ADCH[4:0] do not
decode to all 1s. The ADC10 will continue to convert until the MCU enters reset, the MCU enters stop
mode (if ACLKEN is clear), ADCLK is written, or until ADSCR is written again. If stop is entered (with
ACLKEN low), continuous conversions will cease and can be restarted only with a write to ADSCR.
Any write to ADSCR with ADCO set and the ADCH bits not all 1s will abort the current conversion and
begin continuous conversions.
1 = Conversion completed
0 = Conversion not completed
1 = ADC10 interrupt enabled
0 = ADC10 interrupt disabled
ADC10 status and control register, ADSCR
ADC10 data registers, ADRH and ADRL
ADC10 clock register, ADCLK
Reset:
Read:
Write:
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
Figure 3-3. ADC10 Status and Control Register (ADSCR)
COCO
Bit 7
0
= Unimplemented
AIEN
6
0
ADCO
5
0
ADCH4
4
1
ADCH3
3
1
ADCH2
2
1
ADCH1
1
1
Freescale Semiconductor
ADCH0
Bit 0
1
SSA
.