MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 157

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

14.4.2.1 Power-On Reset
When power is first applied to the MCU, the power-on reset module (POR) generates a pulse to indicate
that power on has occurred. The SIM counter counts out 4096 BUSCLKX4 cycles. Sixty-four BUSCLKX4
cycles later, the CPU and memories are released from reset to allow the reset vector sequence to occur.
At power on, the following events occur:
See
14.4.2.2 Computer Operating Properly (COP) Reset
An input to the SIM is reserved for the COP reset signal. The overflow of the COP counter causes an
internal reset and sets the COP bit in the SIM reset status register (SRSR). The SIM actively pulls down
the RST pin for all internal reset sources.
To prevent a COP module time out, write any value to location $FFFF. Writing to location $FFFF clears
the COP counter and stages 12–5 of the SIM counter. The SIM counter output, which occurs at least
every 4080 BUSCLKX4 cycles, drives the COP counter. The COP should be serviced as soon as possible
out of reset to guarantee the maximum amount of time before the first time out.
The COP module is disabled during a break interrupt with monitor mode when BDCOP bit is set in break
auxiliary register (BRKAR).
Freescale Semiconductor
•
•
•
•
•
Figure
ADDRESS BUS
A POR pulse is generated.
The internal reset signal is asserted.
The SIM enables the oscillator to drive BUSCLKX4.
Internal clocks to the CPU and modules are held inactive for 4096 BUSCLKX4 cycles to allow
stabilization of the oscillator.
The POR bit of the SIM reset status register (SRSR) is set.
BUSCLKX4
BUSCLKX2
PORRST
OSC1
14-6.
RST
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
CYCLES
4096
Figure 14-6. POR Recovery
(RST PIN IS A GENERAL-PURPOSE INPUT AFTER A POR)
CYCLES
32
CYCLES
32
$FFFE
Reset and System Initialization
$FFFF
157