MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 141

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

13.8.4 ESCI Status Register 1
ESCI status register 1 (SCS1) contains flags to signal these conditions:
SCTE — ESCI Transmitter Empty Bit
TC — Transmission Complete Bit
SCRF — ESCI Receiver Full Bit
IDLE — Receiver Idle Bit
Freescale Semiconductor
•
•
•
•
•
•
•
•
This clearable, read-only bit is set when the SCDR transfers a character to the transmit shift register.
SCTE can generate an ESCI transmitter interrupt request. When the SCTIE bit in SCC2 is set, SCTE
generates an ESCI transmitter interrupt request. In normal operation, clear the SCTE bit by reading
SCS1 with SCTE set and then writing to SCDR
This read-only bit is set when the SCTE bit is set, and no data, preamble, or break character is being
transmitted. TC generates an ESCI transmitter interrupt request if the TCIE bit in SCC2 is also set. TC
is cleared automatically when data, preamble, or break is queued and ready to be sent. There may be
up to 1.5 transmitter clocks of latency between queueing data, preamble, and break and the
transmission actually starting.
This clearable, read-only bit is set when the data in the receive shift register transfers to the ESCI data
register. SCRF can generate an ESCI receiver interrupt request. When the SCRIE bit in SCC2 is set
the SCRF generates a interrupt request. In normal operation, clear the SCRF bit by reading SCS1 with
SCRF set and then reading the SCDR.
This clearable, read-only bit is set when 10 or 11 consecutive 1s appear on the receiver input. IDLE
generates an ESCI receiver interrupt request if the ILIE bit in SCC2 is also set. Clear the IDLE bit by
reading SCS1 with IDLE set and then reading the SCDR. After the receiver is enabled, it must receive
1 = SCDR data transferred to transmit shift register
0 = SCDR data not transferred to transmit shift register
1 = No transmission in progress
0 = Transmission in progress
1 = Received data available in SCDR
0 = Data not available in SCDR
Transfer of SCDR data to transmit shift register complete
Transmission complete
Transfer of receive shift register data to SCDR complete
Receiver input idle
Receiver overrun
Noisy data
Framing error
Parity error
Reset:
Read:
Write:
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
SCTE
Bit 7
1
Figure 13-12. ESCI Status Register 1 (SCS1)
= Unimplemented
TC
6
1
SCRF
5
0
IDLE
4
0
OR
3
0
NF
2
0
FE
1
0
Bit 0
PE
0
Registers
141