MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 181

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

In a slave SPI (MSTR = 0), MODF generates an SPI receiver/error interrupt request if the ERRIE bit is
set. The MODF bit does not clear the SPE bit or reset the SPI in any way. Software can abort the SPI
transmission by clearing the SPE bit of the slave.
To clear the MODF flag, read the SPSCR with the MODF bit set and then write to the SPCR register. This
entire clearing mechanism must occur with no MODF condition existing or else the flag is not cleared.
15.4 Interrupts
Four SPI status flags can be enabled to generate interrupt requests. See
Reading the SPI status and control register with SPRF set and then reading the receive data register
clears SPRF. The clearing mechanism for the SPTE flag is requires only a write to the transmit data
register.
The SPI transmitter interrupt enable bit (SPTIE) enables the SPTE flag to generate transmitter interrupt
requests, provided that the SPI is enabled (SPE = 1).
The SPI receiver interrupt enable bit (SPRIE) enables SPRF to generate receiver interrupt requests,
regardless of the state of SPE. See
Freescale Semiconductor
A high on the SS pin of a slave SPI puts the MISO pin in a high impedance
state. Also, the slave SPI ignores all incoming SPSCK clocks, even if it was
already in the middle of a transmission.
SPTE — Transmitter empty
SPRF — Receiver full
OVRF — Overflow
MODF — Mode fault
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
ERRIE
MODF
OVRF
Flag
Figure 15-11. SPI Interrupt Request Generation
SPRIE
SPTE
Figure
Table 15-1. SPI Interrupts
SPTIE
SPRF
SPI transmitter interrupt request (SPTIE = 1, SPE = 1)
SPI receiver interrupt request (SPRIE = 1)
SPI receiver/error interrupt request (ERRIE = 1)
SPI receiver/error interrupt request (ERRIE = 1)
15-11.
SPE
NOTE
Request
SPI TRANSMITTER
INTERRUPT REQUEST
SPI RECEIVER/ERROR
INTERRUPT REQUEST
Table
15-1.
Interrupts
181