MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 155

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

14.3.1 Bus Timing
In user mode, the internal bus frequency is the oscillator frequency (BUSCLKX4) divided by four.
14.3.2 Clock Start-Up from POR
When the power-on reset module generates a reset, the clocks to the CPU and peripherals are inactive
and held in an inactive phase until after the 4096 BUSCLKX4 cycle POR time out has completed. The
IBUS clocks start upon completion of the time out.
14.3.3 Clocks in Stop Mode and Wait Mode
Upon exit from stop mode by an interrupt or reset, the SIM allows BUSCLKX4 to clock the SIM counter.
The CPU and peripheral clocks do not become active until after the stop delay time out. This time out is
selectable as 4096 or 32 BUSCLKX4 cycles. See
In wait mode, the CPU clocks are inactive. The SIM also produces two sets of clocks for other modules.
Refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode.
Some modules can be programmed to be active in wait mode.
14.4 Reset and System Initialization
The MCU has these reset sources:
All of these resets produce the vector $FFFE–FFFF ($FEFE–FEFF in monitor mode) and assert the
internal reset signal (IRST). IRST causes all registers to be returned to their default values and all
modules to be returned to their reset states.
An internal reset clears the SIM counter (see
the resets sets a corresponding bit in the SIM reset status register (SRSR). See
14.4.1 External Pin Reset
The RST pin circuits include an internal pullup device. Pulling the asynchronous RST pin low halts all
processing. The PIN bit of the SIM reset status register (SRSR) is set as long as RST is held low for at
least the minimum t
if the RSTEN bit is set in the CONFIG2 register.
Freescale Semiconductor
•
•
•
•
•
•
Power-on reset module (POR)
External reset pin (RST)
Computer operating properly module (COP)
Low-voltage inhibit module (LVI)
Illegal opcode
Illegal address
ADDRESS BUS
BUSCLKX2
RL
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
RST
time.
PC
Figure 14-3
Figure 14-3. External Reset Timing
shows the relative timing. The RST pin function is only available
14.5 SIM
14.7.2 Stop
Counter), but an external reset does not. Each of
Mode.
VECT H VECT L
Reset and System Initialization
14.8 SIM
Registers.
155