MC908QC16CDZE Freescale Semiconductor, MC908QC16CDZE Datasheet - Page 118

• Manufacturer Part Number: MC908QC16CDZE
• Description: IC MCU 8BIT 16K FLASH 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QC16CDZE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08QC
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• For Use With: DEMO908QC16 - BOARD DEMO FOR MC908QC16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Periodic Wakeup Module (PWU)
Once the modulo value has been reached, the counter will be reset to $00. The PWU counter is also reset
when the module is disabled, or when the MCU enters stop mode with SMODE clear.
The periodic wakeup RC oscillator is highly dependent on operating voltage and temperature and
consequently would provide limited accuracy if used as a time-keeping function.
12.4 Interrupts
The following PWU source can generate interrupt requests:
12.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby modes.
12.5.1 Wait Mode
The PWU module remains active in wait mode while the PWUON bit in PWUSC is set. Setting PWUIE in
PWUSC enables PWU interrupts to bring the MCU out of wait mode. If the PWU is not required during
wait mode, power consumption can be reduced by disabling the PWU module (PWUON = 0) before
entering wait mode.
118
Note:
BUSCLKX4
•
PWUCLKSEL
PWUCLKSEL bit, PWUMOD and PWUP registers can only be written to with PWUON=0
STOP is an internal MCU signal and when STOP = 0, indicates the MCU is in stop mode.
RESET is an internal MCU signal, indicates the MCU has taken a reset.
BUSCLKX4 is an internal MCU clock source, used to create the bus frequency for the MCU.
PWUIREQ is an internal MCU signal, used to request an interrupt to the MCU.
PWU flag (PWUF) — The PWUF bit is set when the counter reaches the modulo value
programmed in the PWUMOD register. The PWU interrupt enable bit, PWUIE, enables PWU
interrupt requests. PWUF and PWUIE are in the PWUSC register.
SMODE
STOP
EN
INTERNAL RC
OSCILLATOR
32 kHz
Figure 12-1. Periodic Wakeup Interrupt Request Generation Logic
PWU CLOCK SOURCE
MC68HC908QC16 • MC68HC908QC8 • MC68HC908QC4 Data Sheet, Rev. 5
PWUON
1
0
M
U
X
PWU CLOCK
PWUCLKSEL
PRESCALER
PWUP
CLK
PWU COUNTER
PWUMOD
EN
=?
RST
RESET
COUNTER = PWUMOD
PWUACK
VECTOR FETCH
RESET
DECODER
V
DD
D
E
R
Q
PWUIE
Freescale Semiconductor
PWUIREQ
PWUF