PIC32MX360F512L-80I/PT Microchip Technology, PIC32MX360F512L-80I/PT Datasheet - Page 354

• Manufacturer Part Number: PIC32MX360F512L-80I/PT
• Description: IC PIC MCU FLASH 512K 100-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX360F512L-80I/PT

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-TFQFP
• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC32MX3xx
• Core: MIPS
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: I2C , SPI , UART
• Maximum Clock Frequency: 80 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 2.3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM320001, DM320002, MA320001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: PIC32
• No. Of I/o's: 85
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• No. Of Timers: 6
• Embedded Interface Type: EUART, I2C, PSP, SPI
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1000 - PIC32 BREAKOUT BOARDAC244003 - TEST BD MPLAB REAL ICE LOOPBACKAC244006 - KIT MPLAB REAL ICE TRACEDM320001 - KIT EVAL PIC32 STARTERAC164333 - MODULE SKT FOR PM3 100QFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC32MX FAMILY
14.4
A timer can generate an interrupt on a period match
event or a gate event, caused by the falling edge of the
external gate signal.
A timer sets its corresponding interrupt flag bit, TxIF,
whenever the timer event is generated. Refer to a
specific timer mode for details regarding these event
conditions. When a timer event is generated, the inter-
rupt flag bit is set within 1 PBCLK + 2 SYSCLK cycles.
If the timer interrupt enable bit is set, TxIE = 1, an
interrupt is generated.
EXAMPLE 14-7:
EXAMPLE 14-8:
DS61143B-page 352
T4CON = 0x0;
T5CON = 0x0;
T4CONSET = 0x0038;
TMR4= 0x0;
PR4 = 0xFFFFFFFF;
IPC5SET = 0x00000004; // Set priority level=1 and
IPC5SET = 0x00000001; // Set subpriority level=1
IFS0CLR = 0x10000000; // Clear the Timer5 interrupt status flag
IEC0SET = 0x10000000; // Enable Timer5 interrupts
T4CONSET = 0x8000;
T2CON = 0x0;
TMR2 = 0x0;
PR2 = 0xFFFF;
IPC2SET = 0x0000000C; // Set priority level=3
IPC2SET = 0x00000001; // Set subpriority level=1
IFS0CLR = 0x00000100; // Clear Timer interrupt status flag
IEC0SET = 0x00000100; // Enable Timer interrupts
T2CONSET = 0x8000;
Timer Interrupts
16-BIT TIMER INTERRUPT AND PRIORITIES
32-BIT TIMER INTERRUPT AND PRIORITIES
// Stop 16-bit Timer4 and clear control register
// Stop 16-bit Timer5 and clear control register
// Enable 32-bit mode, prescaler at 1:8,
// internal clock source
// Clear contents of the TMR4 and TMR5
// registers in one 32-bit load operation
// Load PR4 and PR5 registers with 32-bit value
// 0xFFFFFFFF in one 32-bit load operation
// Could have also done this in single
// operation by assigning IPC5SET = 0x00000005
// Start Timer
// prescaler at 1:1,internal clock source
// Clear timer register
// Load period register
// Could have also done this in single
// operation by assigning IPC2SET = 0x0000000D
// Start Timer
// Stop Timer and clear control register,
Advance Information
The timer module is enabled as a source of interrupts
via the respective Timer Interrupt Enable bit, TxIE
(IECx<n>). The Timer Interrupt Flag, TxIF (IFSx<n>),
must be cleared in software.
The interrupt priority level bits and interrupt subpriority
level bits must be also be configured:
• TxIP<2:0> (IPCx<4:2>)
• TxIS<1:0> (IPCx<1:0)
Setting the timer’s interrupt priority level = 0 effectively
disables the timer’s ability to generate an interrupt.
In addition to enabling the timer interrupt, an Interrupt
Service Routine, ISR, is required. Example 14-7
through Example 14-9 show a partial code example of
an ISR.
© 2008 Microchip Technology Inc.