PIC32MX360F512L-80I/PT Microchip Technology, PIC32MX360F512L-80I/PT Datasheet - Page 555

• Manufacturer Part Number: PIC32MX360F512L-80I/PT
• Description: IC PIC MCU FLASH 512K 100-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX360F512L-80I/PT

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-TFQFP
• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC32MX3xx
• Core: MIPS
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: I2C , SPI , UART
• Maximum Clock Frequency: 80 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 2.3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM320001, DM320002, MA320001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: PIC32
• No. Of I/o's: 85
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• No. Of Timers: 6
• Embedded Interface Type: EUART, I2C, PSP, SPI
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1000 - PIC32 BREAKOUT BOARDAC244003 - TEST BD MPLAB REAL ICE LOOPBACKAC244006 - KIT MPLAB REAL ICE TRACEDM320001 - KIT EVAL PIC32 STARTERAC164333 - MODULE SKT FOR PM3 100QFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

26.2
This describes the operation of the Watchdog Timer
operation and the Power-up Timer
26.2.1
If enabled, the WDT will increment until it overflows or
“times out”. A WDT time-out will force a device Reset,
except during Sleep or Idle modes. To prevent a WDT
time-out Reset, the user must periodically clear the
Watchdog
(WDTCON<0>) bit.
The WDT uses the LPRC oscillator for reliability.
26.2.2
The WDT is enabled or disabled by the device configu-
ration or controlled via software by writing to the
WDTCON register.
26.2.3
If the FWDTEN Configuration bit is set, then the WDT
is always enabled. The WDT ON control bit
(WDTCON<15>) will reflect this by reading a ‘1’. In this
mode, the ON bit cannot be cleared in software. This bit
will not be cleared by any form of Reset. To disable the
WDT in this mode, the configuration must be rewritten
to the device.
26.2.4
If the FWDTEN Configuration bit is a ‘0’, then the WDT
can be enabled or disabled (the default condition) by
software. In this mode, the ON (WDTCON<15>) bit
reflects the status of the WDT under software control.
A ‘1’ indicates the WDT is enabled and a ‘0’ indicates it
is disabled.
The WDT is enabled in software by setting the WDT
ON control bit. The WDT ON control bit is cleared on
any device Reset, The bit is not cleared upon a wake
from Sleep or exit from Idle mode. The software WDT
option allows the user to enable the WDT for critical
code segments and disable the WDT during noncritical
segments for maximum power savings. This bit can
also be used to disable the WDT while the part is
awake to eliminate the need for WDT servicing, and
then re-enable it before the device is put into Idle or
Sleep to wake the part at a later time.
© 2008 Microchip Technology Inc.
Note:
Note:
Watchdog Timer and Power-Up
Timer Operation
WATCHDOG TIMER OPERATION
ENABLING AND DISABLING THE
WDT
DEVICE CONFIGURATION
CONTROLLED WDT
SOFTWARE CONTROLLED WDT
The LPRC is enabled whenever the WDT
is enabled.
The default state for the WDT on an
unprogrammed device is WDT enabled.
Timer
by
setting
the
Advance Information
WDTCLR
26.2.5
The WDT, if enabled, will continue operation in Sleep or
Idle modes. The WDT may be used to wake the device
from Sleep or Idle. When the WDT times out in a Power
Save mode, a Non-Maskable Interrupt (NMI) is gener-
ated and the WDTO (RCON<4>) bit is set. The NMI
vectors execution to the CPU start-up address but does
not reset registers or peripherals. If the device was in
Sleep, the SLEEP (RCON<3>) status bit will also be
set. If the device was in Idle, the IDLE (RCON<2>) sta-
tus bit will also be set. These bits allow the start-up
code to determine the cause of the wake-up.
26.2.6
There will be a time delay between the WDT event in
Sleep and the beginning of code execution. The dura-
tion of this delay consists of the Start-up time for the
oscillator in use and the Power-up Timer delay, if it is
enabled.
Unlike a wake-up from Sleep mode, there are no time
delays associated with wake-up from Idle mode. The
system clock is running during Idle mode; therefore, no
start-up delays are required at wake-up.
26.2.7
The WDT is reset by any of the following:
• On ANY device Reset
• By a WDTCONSET = 0x01 or equivalent
• Execution of a DEBUG command
• Exiting from Idle or Sleep due to an interrupt
26.2.8
The WDT clock source is the internal LPRC oscillator,
which has a nominal frequency of 32 kHz. This creates
a nominal time-out period for the WDT (T
millisecond when no postscaler is used.
instruction during normal execution.
Note:
Note:
PIC32MX FAMILY
WDT OPERATION IN POWER SAVE
MODES
RESETTING THE WDT TIMER
WDT TIMER PERIOD SELECTION
The WDT timer is not reset when the
device enters a Power Save mode. The
WDT should be serviced prior to entering
a Power Save mode.
The WDT time-out period is directly
related to the frequency of the LPRC
oscillator.
oscillator will vary as a function of device
operating
Please refer to the specific PIC32MX
Family device data sheet for LPRC clock
frequency specifications.
TIME DELAYS ON WAKE
The frequency of the LPRC
voltage and temperature.
DS61143B-page 553
WDT
) of 1