PIC32MX360F512L-80I/PT Microchip Technology, PIC32MX360F512L-80I/PT Datasheet - Page 480

• Manufacturer Part Number: PIC32MX360F512L-80I/PT
• Description: IC PIC MCU FLASH 512K 100-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX360F512L-80I/PT

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-TFQFP
• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC32MX3xx
• Core: MIPS
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: I2C , SPI , UART
• Maximum Clock Frequency: 80 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 2.3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM320001, DM320002, MA320001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: PIC32
• No. Of I/o's: 85
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• No. Of Timers: 6
• Embedded Interface Type: EUART, I2C, PSP, SPI
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1000 - PIC32 BREAKOUT BOARDAC244003 - TEST BD MPLAB REAL ICE LOOPBACKAC244006 - KIT MPLAB REAL ICE TRACEDM320001 - KIT EVAL PIC32 STARTERAC164333 - MODULE SKT FOR PM3 100QFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

ALRMEN bit is cleared automatically and the alarm will
PIC32MX FAMILY
EXAMPLE 21-4:
21.3.3
A repeat alarm can be generated by configuring the
Alarm Repeat Counter bits, ARPT (RTCALRM<7:0>)
= 0x00 to 0xFF (0 to 255), and the CHIME bit
(RTCALRM<14>) = 0. Once the the alarm is enabled
and an alarm event occurs, the ARPT count is decre-
mented by one. Once the register reaches 0, the alarm
will be generated one last time; after which point,
turn off. The user must re-enable this bit for any new
alarm configuration.
EXAMPLE 21-5:
DS61143B-page 478
/*
*/
/*
*/
Note:
The following code example will update the RTCC one-time alarm.
Assumes the interrupts are disabled.
unsigned long alTime=0x16153300;// set time to 04 hr, 15 min, 33 sec
unsigned long alDate=0x06102705;// set date to Friday 27 Oct 2006
while(RTCALRM&0x1000);
RTCALRMCLR=0xCFFF;
ALRMTIME=alTime;
ALRMDATE=alDate;
RTCALRMSET=0x8000|0x00000600;
The following code example will update the RTCC repeat alarm.
Assumes the interrupts are disabled.
unsigned long alTime=0x23352300;
unsigned long alDate=0x06111301;
while(RTCALRM&0x1000);
RTCALRMCLR=0xCFFF;
ALRMTIME=alTime;
ALRMDATE=alDate;
RTCALRMSET=0x8000|0x0509;
REPEAT ALARM
An alarm event is generated when ARPT
bits are = 0x00.
CONFIGURING THE RTCC FOR A ONE-TIME ALARM
CONFIGURING THE RTCC FOR A TEN TIMES PER HOUR ALARM
// turn off the alarm, chime and alarm repeats; clear
// the alarm mask
// wait ALRMSYNC to be off
// clear ALRMEN, CHIME, AMASK and ARPT;
// update the alarm time and date
// re-enable the alarm, set alarm mask at once per day
Advance Information
// set time to 23hr, 35 min, 23 sec
// set date to Monday 13 Nov 2006
// turn off the alarm, chime and alarm repeats; clear
// the alarm mask
// wait ALRMSYNC to be off
// clear the ALRMEN, CHIME, AMASK and ARPT;
// update the alarm time and date
// re-enable the alarm, set alarm mask at once per hour
// for 10 times repeat
It is recommended to read and verify the Alarm Sync bit
ALRMSYNC (RTCALRM<12>) = 0, before performing
the following configuration steps:
• Disable alarm – ALRMEN (RTCALRM<15>) = 0.
• Disable chime – CHIME (RTCALRM<14>) = 0.
• Configure alarm repeat counter – ARPT
• Configure alarm date and time – Load
• Configure mask – Load the desired AMASK
• Enable alarm – ALRMEN (RTCALRM<15>) = 0.
Refer to Example 21-5.
(RTCALRM<7:0>) = 0x00 to 0xFF.
ALRMDATE and ALRMTIME registers with the
desired alarm date/time values.
value.
© 2008 Microchip Technology Inc.