AT32UC3B1128-AUT Atmel, AT32UC3B1128-AUT Datasheet - Page 102

• Manufacturer Part Number: AT32UC3B1128-AUT
• Description: IC MCU AVR32 128KB FLASH 48-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B1128-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 28
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 28
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP48 - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1101 - KIT DEV/EVAL FOR AVR32 AT32UC3B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

13.6.3
13.6.4
Figure 13-4. Timing Diagram, Asynchronous Interrupts
13.6.5
32059K–03/2011
Non-Maskable Interrupt
Asynchronous Interrupts
Wakeup
rising EDGE or high
rising EDGE or high
EXTINTn/NMI
EIC_WAKE:
ISR.INTn:
LEVEL
LEVEL
CLK_SYNC
The NMI supports the same features as the external interrupts, and is accessed through the
same registers. The description in
instead of the INTn bits.
The NMI is non-maskable within the CPU in the sense that it can interrupt any other execution
mode. Still, as for the other external interrupts, the actual NMI input can be enabled and disabled
by accessing the registers in the EIC.
Each external interrupt can be made asynchronous by writing a one to INTn in the ASYNC reg-
ister. This will route the interrupt signal through the asynchronous path of the module. All edge
interrupts will be interpreted as level interrupts and the filter is disabled. If an interrupt is config-
ured as edge triggered interrupt in asynchronous mode, a zero in EDGE.INTn will be interpreted
as low level, and a one in EDGE.INTn will be interpreted as high level.
EIC_WAKE will be set immediately after the source triggers the interrupt, while the correspond-
ing bit in ISR and the interrupt to the interrupt controller will be set on the next rising edge of
CLK_SYNC. Please refere to
When CLK_SYNC is stopped only asynchronous interrupts remain active, and any short spike
on this interrupt will wake up the device. EIC_WAKE will restart CLK_SYNC and ISR will be
updated on the first rising edge of CLK_SYNC.
The external interrupts can be used to wake up the part from sleep modes. The wakeup can be
interpreted in two ways. If the corresponding bit in IMR is one, then the execution starts at the
interrupt handler for this interrupt. If the bit in IMR is zero, then the execution starts from the next
instruction after the sleep instruction.
Figure 13-4 on page 102
Section 13.6.1
rising EDGE or high
rising EDGE or high
EXTINTn/NMI
EIC_WAKE:
ISR.INTn:
should be followed, accessing the NMI bit
LEVEL
LEVEL
CLK_SYNC
for details.
AT32UC3B
102