AT32UC3B1128-AUT Atmel, AT32UC3B1128-AUT Datasheet - Page 377

• Manufacturer Part Number: AT32UC3B1128-AUT
• Description: IC MCU AVR32 128KB FLASH 48-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B1128-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 28
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 28
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP48 - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1101 - KIT DEV/EVAL FOR AVR32 AT32UC3B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

22.7.1.9
32059K–03/2011
ID detection
In host mode, the USBSTA.VBUS bit follows an hysteresis based on Session_valid and
Va_Vbus_valid:
The VBus Transition interrupt (VBUSTI) bit in USBSTA is set on each transition of the USB-
STA.VBUS bit.
The USBSTA.VBUS bit is effective whether the USBB is enabled or not.
Figure 22-12 on page 377
Figure 22-12. ID Detection Input Block Diagram
The USB mode (device or host) can be either detected from the USB_ID pin or software
selected by writing to the UIMOD bit, according to the UIDE bit. This allows the USB_ID pin to be
used as a general purpose I/O pin even when the USB interface is enabled.
By default, the USB_ID pin is selected (UIDE is written to one) and the USBB is in device mode
(UBSTA.ID is one), what corresponds to the case where no Mini-A plug is connected, i.e. no
plug or a Mini-B plug is connected and the USB_ID pin is kept high by the internal pull-up resis-
tor from the I/O Controller (which must be enabled if USB_ID is used).
The ID Transition Interrupt (IDTI) bit in USBSTA is set on each transition of the ID bit, i.e. when a
Mini-A plug (host mode) is connected or disconnected. This does not occur when a Mini-B plug
(device mode) is connected or disconnected.
The USBSTA.ID bit is effective whether the USBB is enabled or not.
• It is cleared when the voltage on the VBUS pad is lower than 1.4V.
• It is set when the voltage on the USB_VBUS pad is higher than or equal to 4.4V.
• It is cleared when the voltage on the USB_VBUS pad is lower than 1.4V.
USB_ID
I/O Controller
VDD
shows how the ID transitions are detected.
UIMOD
USBCON
USBCON
1
0
UIDE
USBSTA
ID
AT32UC3B
USBSTA
IDTI
377