AT32UC3B1128-AUT Atmel, AT32UC3B1128-AUT Datasheet - Page 42

• Manufacturer Part Number: AT32UC3B1128-AUT
• Description: IC MCU AVR32 128KB FLASH 48-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B1128-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 28
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 28
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP48 - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1101 - KIT DEV/EVAL FOR AVR32 AT32UC3B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

9.5.7
9.5.7.1
9.5.7.2
Table 9-1.
32059K–03/2011
Index
0
1
2
3
4
5
Sleep modes
Sleep Mode
Idle
Frozen
Standby
Stop
DeepStop
Static
Entering and exiting sleep modes
Supported sleep modes
Sleep modes
In normal operation, all clock domains are active, allowing software execution and peripheral
operation. When the CPU is idle, it is possible to switch off the CPU clock and optionally other
clock domains to save power. This is activated by the sleep instruction, which takes the sleep
mode index number as argument.
The sleep instruction will halt the CPU and all modules belonging to the stopped clock domains.
The modules will be halted regardless of the bit settings of the mask registers.
Oscillators and PLLs can also be switched off to save power. Some of these modules have a rel-
atively long start-up time, and are only switched off when very low power consumption is
required.
The CPU and affected modules are restarted when the sleep mode is exited. This occurs when
an interrupt triggers. Note that even if an interrupt is enabled in sleep mode, it may not trigger if
the source module is not clocked.
The following sleep modes are supported. These are detailed in
•Idle: The CPU is stopped, the rest of the chip is operating. Wake-up sources are any interrupt.
•Frozen: The CPU and HSB modules are stopped, peripherals are operating. Wake-up sources
are any interrupts from PB modules.
•Standby: All synchronous clocks are stopped, but oscillators and PLLs are running, allowing
quick wake-up to normal mode. Wake-up sources are RTC or external interrupt (EIC), external
reset or any asynchronous interrupts from PB modules.
•Stop: As Standby, but Oscillator 0 and 1, and the PLLs are stopped. 32 KHz (if enabled) and
RC oscillators and RTC/WDT will still operate. Wake-up are the same as for Standby mode.
•DeepStop: All synchronous clocks, Oscillator 0 and 1 and PLL 0 and 1 are stopped. 32 KHz
oscillator can run if enabled. RC oscillator still operates. Bandgap voltage reference and BOD is
turned off. Wake-up sources are RTC, external interrupt in asynchronous mode, external reset
or any asynchronous interrupts from PB modules.
•Static: All oscillators, including 32 KHz and RC oscillator are stopped. Bandgap voltage refer-
ence BOD detector is turned off. Wake-up sources are external interrupt (EIC) in asynchronous
mode only, external reset pin or any asynchronous interrupts from PB modules.
CPU
Stop
Stop
Stop
Stop
Stop
Stop
HSB
Run
Stop
Stop
Stop
Stop
Stop
PBA,B
GCLK
Run
Run
Stop
Stop
Stop
Stop
Osc0,1
PLL0,1,
SYSTIMER
Run
Run
Run
Stop
Stop
Stop
Osc32
Run
Run
Run
Run
Stop
Run
RCOsc
Run
Run
Run
Run
Run
Stop
Table
9-1.
BOD &
Bandgap
On
On
On
On
Off
Off
AT32UC3B
Voltage
Regulator
Full power
Full power
Full power
Low power
Low power
Low power
42