AT32UC3B1128-AUT Atmel, AT32UC3B1128-AUT Datasheet - Page 384

• Manufacturer Part Number: AT32UC3B1128-AUT
• Description: IC MCU AVR32 128KB FLASH 48-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B1128-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 28
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 28
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP48 - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1101 - KIT DEV/EVAL FOR AVR32 AT32UC3B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

22.7.2.12
32059K–03/2011
Management of IN endpoints
•Overview
TXINI
FIFOCON
IN packets are sent by the USB device controller upon IN requests from the host. All the data
can be written which acknowledges or not the bank when it is full.
The endpoint must be configured first.
The TXINI bit is set at the same time as FIFOCON when the current bank is free. This triggers
an EPnINT interrupt if the Transmitted IN Data Interrupt Enable (TXINE) bit in UECONn is one.
TXINI shall be cleared by software (by writing a one to the Transmitted IN Data Interrupt Enable
Clear bit in the Endpoint n Control Clear register (UECONnCLR.TXINIC)) to acknowledge the
interrupt, what has no effect on the endpoint FIFO.
The user then writes into the FIFO (see
DATA)” on page
UECONnCLR to clear the FIFOCON bit. This allows the USBB to send the data. If the IN end-
point is composed of multiple banks, this also switches to the next bank. The TXINI and
FIFOCON bits are updated in accordance with the status of the next bank.
TXINI shall always be cleared before clearing FIFOCON.
The RWALL bit is set when the current bank is not full, i.e. the software can write further data
into the FIFO.
Figure 22-17. Example of an IN Endpoint with 1 Data Bank
SW
write data to CPU
NAK
BANK 0
481) and write a one to the FIFO Control Clear (FIFOCONC) bit in
SW
IN
”USB Pipe/Endpoint n FIFO Data Register (USBFIFOn-
(bank 0)
DATA
HW
ACK
SW
write data to CPU
BANK 0
AT32UC3B
SW
IN
384