AT32UC3B1128-AUT Atmel, AT32UC3B1128-AUT Datasheet - Page 191

• Manufacturer Part Number: AT32UC3B1128-AUT
• Description: IC MCU AVR32 128KB FLASH 48-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B1128-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 28
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 28
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP48 - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1101 - KIT DEV/EVAL FOR AVR32 AT32UC3B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

17.7
17.7.1
17.7.2
32059K–03/2011
Programming Examples
8-bit LED-Chaser
Configuration of USART pins
It is assumed in this example that a subroutine "delay" exists that returns after a given time.
The example below shows how to configure a peripheral module to control I/O pins. It assumed
in this example that the USART receive pin (RXD) is connected to PC16 and that the USART
transmit pin (TXD) is connected to PC17. For both pins, the USART is peripheral B. In this
example, the state of the GPIO registers is assumed to be unknown. The two USART pins are
therefore first set to be controlled by the GPIO with output drivers disabled. The pins can then be
assured to be tri-stated while changing the Peripheral Mux Registers.
loop:
// Set R0 to GPIO base address
mov
orh
// Enable GPIO control of pin 0-8
mov
st.w
// Set initial value of port
mov
st.w
// Set up toggle value. Two pins are toggled
// in each round. The bit that is currently set,
// and the next bit to be set.
mov
orh
// Only change 8 LSB
mov
and
st.w
rol
rcall
rjmp
// Set up pointer to GPIO, PORTC
mov
orh
// Disable output drivers
R0, LO(AVR32_GPIO_ADDRESS)
R0, HI(AVR32_GPIO_ADDRESS)
R1, 0xFF
R0[AVR32_GPIO_GPERS], R1
R2, 0x01
R0[AVR32_GPIO_OVRS], R2
R2, 0x0303
R2, 0x0303
R3, 0x00FF
R3, R2
R0[AVR32_GPIO_OVRT], R3
R2
delay
loop
R0, LO(AVR32_GPIO_ADDRESS + PORTC_OFFSET)
R0, HI(AVR32_GPIO_ADDRESS + PORTC_OFFSET)
AT32UC3B
191