AT32UC3B1128-AUT Atmel, AT32UC3B1128-AUT Datasheet - Page 442

• Manufacturer Part Number: AT32UC3B1128-AUT
• Description: IC MCU AVR32 128KB FLASH 48-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B1128-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 28
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 28
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP48 - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1101 - KIT DEV/EVAL FOR AVR32 AT32UC3B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

22.8.2.14
Register Name:
Access Type:
Offset:
Reset Value:
• STALLRQ: STALL Request
• RSTDT: Reset Data Toggle
• EPDISHDMA: Endpoint Interrupts Disable HDMA Request Enable
• FIFOCON: FIFO Control
32059K–03/2011
PACKETE
SHORT
31
23
15
7
-
-
-
This bit is set when the STALLRQS bit is written to one. This will request to send a STALL handshake to the host.
This bit is cleared when a new SETUP packet is received or when the STALLRQC bit is written to zero.
This bit is set when the RSTDTS bit is written to one. This will clear the data toggle sequence, i.e., set to Data0 the data toggle
sequence of the next sent (IN endpoints) or received (OUT endpoints) packet.
This bit is cleared instantaneously.
The user does not have to wait for this bit to be cleared.
This bit is set when the EPDISHDMAS is written to one. This will pause the on-going DMA channel n transfer on any Endpoint n
interrupt (EPnINT), whatever the state of the Endpoint n Interrupt Enable bit (EPnINTE).
The user then has to acknowledge or to disable the interrupt source (e.g. RXOUTI) or to clear the EPDISHDMA bit (by writing a
one to the EPDISHDMAC bit) in order to complete the DMA transfer.
In ping-pong mode, if the interrupt is associated to a new system-bank packet (e.g. Bank1) and the current DMA transfer is
running on the previous packet (Bank0), then the previous-packet DMA transfer completes normally, but the new-packet DMA
transfer will not start (not requested).
If the interrupt is not associated to a new system-bank packet (NAKINI, NAKOUTI, etc.), then the request cancellation may
occur at any time and may immediately pause the current DMA transfer.
This may be used for example to identify erroneous packets, to prevent them from being transferred into a buffer, to complete a
DMA transfer by software after reception of a short packet, etc.
For control endpoints:
The FIFOCON and RWALL bits are irrelevant. The software shall therefore never use them on these endpoints. When read,
their value is always 0.
For IN endpoints:
This bit is set when the current bank is free, at the same time as TXINI.
Endpoint n Control Register
STALLEDE/
CRCERRE
FIFOCON
30
22
14
6
-
-
UECONn, n in [0..6]
Read-Only
0x01C0 + (n * 0x04)
0x00000000
OVERFE
KILLBK
29
21
13
5
-
-
NBUSYBKE
NAKINE
28
20
12
4
-
-
NAKOUTE
STALLRQ
27
19
11
3
-
-
UNDERFE
RXSTPE/
RSTDT
26
18
10
2
-
-
RXOUTE
25
17
9
1
-
-
-
AT32UC3B
EPDISHDMA
TXINE
24
16
8
0
-
-
442