AT32UC3B1128-AUT Atmel, AT32UC3B1128-AUT Datasheet - Page 402

• Manufacturer Part Number: AT32UC3B1128-AUT
• Description: IC MCU AVR32 128KB FLASH 48-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B1128-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 28
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 28
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP48 - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1101 - KIT DEV/EVAL FOR AVR32 AT32UC3B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

32059K–03/2011
The UDDMAnSTATUS.CHEN bit is 0 and the UDDMAnSTATUS.LDNXTCHDESCEN is set indi-
cating that the DMA channel is pending until the endpoint is ready (received OUT packet).
As soon as an OUT packet is stored inside the endpoint, the UDDMAnSTATUS.CHACTIVE bit
is set to one. Then after a few cycle latency, the new descriptor is loaded from the memory and
the UDDMAnSTATUS.DESCLDSTA is set.
At the end of this DMA (for instance when the channel byte length has reached 0), the
UDDMAnCONTROL.CHEN bit is cleared, and then the UDDMAnSTATUS.CHEN bit is also
cleared. If the UDDMAnCONTROL.LDNXTCH value is one, a new descriptor is loaded.
This sequence is repeated until a last linked descriptor is processed. The last descriptor is
detected according to row 2 as shown in
At the end of the last descriptor, the UDDMAnCONTROL.CHEN bit is cleared. As a conse-
quence, after a few cycles latency, the UDDMAnSTATUS.CHEN bit is also cleared.
• Set up the chain of linked list of descripor in memory. Each descriptor is composed of 3 items
• Program the UDDMAnNEXTDESC register.
• Program the UDDMAnCONTROL according to Row 3 as shown in
: channel next descriptor address, channel destination address and channel control. The last
descriptor should be programmed according to row 2 as shown in
Figure 22-6 on page
449.
Figure 22-6 on page
Figure 22-6 on page
AT32UC3B
449.
449.
402