LU82551QM Intel, LU82551QM Datasheet - Page 16

• Manufacturer Part Number: LU82551QM
• Manufacturer: Intel

Specifications of LU82551QM

• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 196
• Lead Free Status / RoHS Status: Compliant

82551QM — Networking Silicon
4.3
10
Table 5.
Table 6.
Note: All unused Flash Address and Data pins MUST be left floating. Some of these pins have
System and Power Management Signals
Local Memory Interface Signals
undocumented test functionality and can cause unpredictable behavior if they are
unnecessarily connected to a pull-up or pull-down resistor.
Local Memory Interface Signals
CSTSCHG/
WOL
ISOLATE#
ALTRST#
VIO
FLD7:0
FLA16/
CLK25
FLA15/EESK
FLA14/
EEDO
FLA13/EEDI
Symbol
Symbol
OUT
IN
IN
B
IN
IN/OUT
IN/OUT
OUT
IN/OUT
OUT
Type
Type
Card Status Change/Wake on LAN*. This pin is multiplexed to
provide Card Status Change or Wake on LAN signals. In a CardBus
system, it is used as the Card Status Change output signal and is an
asynchronous signal to the Clock signal. It indicates that a power
management event has occurred in a CardBus system. In a PCI
system, it is used as the WOL pin and provides a positive pulse of
approximately 52 ms upon detection of an incoming Magic Packet*.
Isolate. The Isolate pin is used to isolate the 82551QM from the PCI
bus. It also provides PCI Reset pin functionality. When Isolate is active
(low), the 82551QM does not drive its PCI outputs (except PME# and
CSTSCHG) or sample its PCI inputs (including CLK and RST#). The
ISOLATE# pin should be driven by the PCI Reset signal.
Alternate Reset. The Alternate Reset pin is used to reset the
82551QM on power-up. The Alternate Reset signal should be pulled
high to the main digital power supply.
Voltage Input/Output. The VIO pin is the voltage bias pin and should
be connected to a 5 V supply in a 5 V PCI signaling environment and a
3.3 V supply in 3.3 V signaling environment. For CardBus systems, it
should be connected to the main digital power supply.
Flash/Modem Data Input/Output. These pins are used for Flash/
Modem data interface. These pins should be left floating if the Flash
and modem are not used.
Flash Address 16/25 MHz Clock. This multiplexed pin is controlled
by the status of the Flash Address 7 (FLA7) pin. If FLA7 is left floating,
this pin is used as FLA16; otherwise, if FLA7 is connected to a pull-up
resistor, this pin is used as a 25 MHz clock output. This pin should be
left floating if the Flash and the CLK25 functionality are not used.
Flash Address 15/EEPROM Data Output. During Flash accesses,
this multiplexed pin acts as the Flash Address 15 output signal. During
EEPROM accesses, it acts as the serial shift clock output to the
EEPROM.
Flash Address 14/EEPROM Data Output. During Flash accesses,
this multiplexed pin acts as the Flash Address 14 output signal. During
EEPROM accesses, this pin accepts serial input data from the
EEPROM Data Output pin.
Flash Address 13/EEPROM Data Input. During Flash accesses, this
multiplexed pin acts as the Flash Address 13 output signal. During
EEPROM accesses, this pin provides serial output data to the
EEPROM Data Input pin.
Name and Function
Name and Function
Datasheet