ATMEGA16HVA-4CKU Atmel, ATMEGA16HVA-4CKU Datasheet - Page 152

• Manufacturer Part Number: ATMEGA16HVA-4CKU
• Description: MCU AVR 16K FLASH 4MHZ 36-LGA
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16HVA-4CKU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 7
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 9 V
• Data Converters: A/D 5x12b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 36-LGA
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRSB200, ATAVRSB201
• Minimum Operating Temperature: - 20 C
• On-chip Adc: 12 bit, 5 Channel
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

27.6.1
152
ATmega8HVA/16HVA
Serial Programming Algorithm
Figure 27-1. Serial Programming and Verify.
Table 27-8.
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on OSCSEL Fuses, a valid clock must be present. The minimum low and high peri-
ods for the serial clock (SCK) input are defined as follows:
Low: > 2.2 CPU clock cycles for f
High: > 2.2 CPU clock cycles for f
When writing serial data to the ATmega8HVA/16HVA, data is clocked on the rising edge of SCK.
When reading data from the ATmega8HVA/16HVA, data is clocked on the falling edge of SCK.
See
To program and verify the ATmega8HVA/16HVA in the Serial Programming mode, the following
sequence is recommended (see four byte instruction formats in
1. Power-up sequence:
2. Wait for at least 20 ms and enable serial programming by sending the Programming
Apply power between V
tems, the programmer can not guarantee that SCK is held low during power-up. In this
case, RESET must be given a positive pulse of at least two CPU clock cycles duration
after SCK has been set to “0”.
Enable serial instruction to pin MOSI.
”Serial Programming” on page 172
Symbol
MOSI
MISO
SCK
Pin Mapping Serial Programming
MOSI
MISO
SCK
CC
and GND while RESET and SCK are set to “0”. In some sys-
Pins
PB1
PB2
PB3
ck
ck
< 12 MHz, 3 CPU clock cycles for f
< 12 MHz, 3 CPU clock cycles for f
RESET
GND
for timing details.
I/O
O
I
I
VCC
+3.0 - 4.5V
Table 27-10 on page
Serial Data out
Serial Data in
Description
Serial Clock
ck
ck
>= 12 MHz
>= 12 MHz
8024A–AVR–04/08
154):