PIC18F8722-I/PT Microchip Technology Inc., PIC18F8722-I/PT Datasheet - Page 126

• Manufacturer Part Number: PIC18F8722-I/PT
• Description: 80 PIN, 128 KB FLASH, 4K RAM, 70 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F8722-I/PT

• A/d Inputs: 16-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 70
• Interface: SPI/I2C/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 80-pin TQFP
• Programmable Memory: 128K Bytes
• Ram Size: 3.9K Bytes
• Speed: 40 MHz
• Timers: 2-8 bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F8722 FAMILY
10.2
The PIR registers contain the individual flag bits for the
peripheral interrupts. Due to the number of peripheral
interrupt sources, there are three Peripheral Interrupt
Request (Flag) registers (PIR1, PIR2, PIR3).
REGISTER 10-4:
DS39646B-page 124
PIR Registers
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1
bit 7
PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write has occurred
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
RC1IF: EUSART1 Receive Interrupt Flag bit
1 = The EUSART1 receive buffer, RCREG1, is full (cleared when RCREG1 is read)
0 = The EUSART1 receive buffer is empty
TX1IF: EUSART1 Transmit Interrupt Flag bit
1 = The EUSART1 transmit buffer, TXREG1, is empty (cleared when TXREG1 is written)
0 = The EUSART1 transmit buffer is full
SSP1IF: MSSP1 Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
CCP1IF: ECCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1/TMR3 register capture occurred (must be cleared in software)
0 = No TMR1/TMR3 register capture occurred
Compare mode:
1 = A TMR1/TMR3 register compare match occurred (must be cleared in software)
0 = No TMR1/TMR3 register compare match occurred
PWM mode:
Unused in this mode.
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
Legend:
R = Readable bit
-n = Value at POR
PSPIF
R/W-0
R/W-0
ADIF
RC1IF
R-0
Preliminary
W = Writable bit
‘1’ = Bit is set
TX1IF
R-0
Note 1: Interrupt flag bits are set when an interrupt
2: User
SSP1IF
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
condition occurs, regardless of the state
of its corresponding enable bit or the
Global
(INTCON<7>).
appropriate interrupt flag bits are cleared
prior to enabling an interrupt and after
servicing that interrupt.
software
CCP1IF
R/W-0
Interrupt
 2004 Microchip Technology Inc.
should
TMR2IF
R/W-0
Enable
x = Bit is unknown
ensure
bit,
TMR1IF
R/W-0
bit 0
GIE
the