PIC18F8722-I/PT Microchip Technology Inc., PIC18F8722-I/PT Datasheet - Page 213

• Manufacturer Part Number: PIC18F8722-I/PT
• Description: 80 PIN, 128 KB FLASH, 4K RAM, 70 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F8722-I/PT

• A/d Inputs: 16-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 70
• Interface: SPI/I2C/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 80-pin TQFP
• Programmable Memory: 128K Bytes
• Ram Size: 3.9K Bytes
• Speed: 40 MHz
• Timers: 2-8 bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

19.3.6
In Slave mode, the data is transmitted and received as
the external clock pulses appear on SCKx. When the
last bit is latched, the SSPxIF interrupt flag bit is set.
While in Slave mode, the external clock is supplied by
the external clock source on the SCKx pin. This exter-
nal clock must meet the minimum high and low times
as specified in the electrical specifications.
While in Sleep mode, the slave can transmit/receive
data. When a byte is received, the device can be
configured to wake-up from Sleep.
19.3.7
The SSx pin allows a Synchronous Slave mode. The
SPI must be in Slave mode with the SSx pin control
enabled (SSPxCON1<3:0> = 04h). When the SSx pin
is low, transmission and reception are enabled and the
SDOx pin is driven. When the SSx pin goes high, the
SDOx pin is no longer driven, even if in the middle of a
FIGURE 19-4:
 2004 Microchip Technology Inc.
SSx
SCKx
(CKP = 0
CKE = 0)
SCKx
(CKP = 1
CKE = 0)
Write to
SSPxBUF
SDOx
SDIx
(SMP = 0)
Input
Sample
(SMP = 0)
SSPxIF
Interrupt
Flag
SSPxSR to
SSPxBUF
SLAVE MODE
SLAVE SELECT
SYNCHRONIZATION
SLAVE SYNCHRONIZATION WAVEFORM
bit 7
bit 7
bit 6
Preliminary
transmitted byte and becomes a floating output. Exter-
nal pull-up/pull-down resistors may be desirable
depending on the application.
When the SPI module resets, the bit counter is forced
to ‘0’. This can be done by either forcing the SSx pin to
a high level or clearing the SSPEN bit.
To emulate two-wire communication, the SDOx pin can
be connected to the SDIx pin. When the SPI needs to
operate as a receiver, the SDOx pin can be configured
as an input. This disables transmissions from the
SDOx. The SDIx can always be left as an input (SDI
function) since it cannot create a bus conflict.
PIC18F8722 FAMILY
Note 1: When the
2: If the SPI is used in Slave mode with CKE
with
(SSPxCON1<3:0> = 0100),
module will reset if the SSx pin is set to V
set, then the SSx pin control must be
enabled.
bit 7
bit 7
SSx
SPI
pin
is in Slave mode
Next Q4 Cycle
after Q2↓
control
DS39646B-page 211
bit 0
bit 0
the
enabled
SPI
DD
.