PIC18F8722-I/PT Microchip Technology Inc., PIC18F8722-I/PT Datasheet - Page 189

• Manufacturer Part Number: PIC18F8722-I/PT
• Description: 80 PIN, 128 KB FLASH, 4K RAM, 70 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F8722-I/PT

• A/d Inputs: 16-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 70
• Interface: SPI/I2C/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 80-pin TQFP
• Programmable Memory: 128K Bytes
• Ram Size: 3.9K Bytes
• Speed: 40 MHz
• Timers: 2-8 bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

18.0
In the PIC18F8722 family of devices, ECCP1, ECCP2
and ECCP3 are implemented as a standard CCP
module with Enhanced PWM capabilities. These
include the provision for 2 or 4 output channels, user
selectable polarity, dead-band control and automatic
shutdown and restart. The enhanced features are
discussed in detail in Section 18.4 “Enhanced PWM
Mode”. Capture, Compare and single-output PWM
functions of the ECCP module are the same as
described for the standard CCP module.
REGISTER 18-1:
 2004 Microchip Technology Inc.
ENHANCED CAPTURE/
COMPARE/PWM (ECCP)
MODULE
bit 7-6
bit 5-4
bit 3-0
CCPxCON: ENHANCED CCPx CONTROL REGISTER (ECCP1, ECCP2, ECCP3)
Legend:
R = Readable bit
-n = Value at POR
bit 7
PxM1:PxM0: Enhanced PWM Output Configuration bits
If CCPxM3:CCPxM2 = 00, 01, 10:
xx = PxA assigned as Capture/Compare input/output; PxB, PxC, PxD assigned as port pins
If CCPxM3:CCPxM2 = 11:
00 = Single output: PxA modulated; PxB, PxC, PxD assigned as port pins
01 = Full-bridge output forward: P1D modulated; P1A active; P1B, P1C inactive
10 = Half-bridge output: P1A, P1B modulated with dead-band control; P1C, P1D assigned as
11 = Full-bridge output reverse: P1B modulated; P1C active; P1A, P1D inactive
DCxB1:DCxB0: PWM Duty Cycle bit 1 and bit 0
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are
found in CCPRxL.
CCPxM3:CCPxM0: Enhanced CCP Mode Select bits
0000 = Capture/Compare/PWM off (resets ECCPx module)
0001 = Reserved
0010 = Compare mode: toggle output on match
0011 = Capture mode
0100 = Capture mode: every falling edge
0101 = Capture mode: every rising edge
0110 = Capture mode: every 4th rising edge
0111 = Capture mode: every 16th rising edge
1000 = Compare mode: initialize ECCPx pin low; set output on compare match (set CCPxIF)
1001 = Compare mode: initialize ECCPx pin high; clear output on compare match (set CCPxIF)
1010 = Compare mode: generate software interrupt only; ECCPx pin reverts to I/O state
1011 = Compare mode: trigger special event (ECCP resets TMR1 or TMR3, sets CCPxIF bit;
1100 = PWM mode: PxA, PxC active-high; PxB, PxD active-high
1101 = PWM mode: PxA, PxC active-high; PxB, PxD active-low
1110 = PWM mode: PxA, PxC active-low; PxB, PxD active-high
1111 = PWM mode: PxA, PxC active-low; PxB, PxD active-low
R/W-0
PxM1
port pins
ECCP2 trigger starts A/D conversion if A/D module is enabled)
R/W-0
PxM0
DCxB1
R/W-0
W = Writable bit
‘1’ = Bit is set
Preliminary
DCxB0
R/W-0
The control register for the Enhanced CCP modules is
shown in Register 18-1. It differs from the CCPxCON
registers
Compare/PWM (CCP) Modules” in that the two Most
Significant bits are implemented to control PWM
functionality. In addition to the expanded range of
modes available through the Enhanced CCPxCON
register, the ECCP modules each have two additional
features associated with Enhanced PWM operation
and auto-shutdown features. They are:
• ECCPxDEL (Dead-Band Delay)
• ECCPxAS (Auto-Shutdown Configuration)
PIC18F8722 FAMILY
CCPxM3
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
discussed
CCPxM2
R/W-0
in
Section 17.0
x = Bit is unknown
CCPxM1
R/W-0
DS39646B-page 187
CCPxM0
“Capture/
R/W-0
bit 0