TMPM333FDFG Toshiba, TMPM333FDFG Datasheet - Page 42

• Manufacturer Part Number: TMPM333FDFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 512K FLASH, 32K SRAM
• Manufacturer: Toshiba

Specifications of TMPM333FDFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 512K
• Rom Type: Flash
• Ram (kbytes): 32K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: -
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

3.4
Pin Functions
3.4
The PB0 pin is shared between the JTAG debug port function and the SWV trace output function.
debug interface pins need to be programmed as required.
Note 1: If PA0 and PB0 are configured as TMS/SWDIO and TDO/SWV, output continues to be enabled even in STOP mode
Note 2: If PA1 is configured as a debug function pin, it prevents a low power consumption mode from being fully effective. Configure
Pin Functions
The debug interface pins can also be used as general-purpose ports.
The PA0 and PA1 pins are shared between the JTAG debug port function and the Serial Wire Debug Port function.
After reset, PA0, PA1, PB0, PB1 and PB2 pins are configured as debug port function pins. The functions of other
When using a low power consumption mode, take note of the following points.
Table 3-2 summarizes the debug interface pin and related port settings after reset.
Note:When SWV function is enabled.
Table 3-1 SWJ-DP,ETM Debug Functions
TRACEDATA0
TRACEDATA1
TRACEDATA2
TRACEDATA3
TMS / SWDIO
TCK / SWCLK
TRACECLK
TDO / SWV
Pin Name
SWJ-DP
TRST
TDI
regardless of the setting of the CGSTBYCR<DRVE> bit.
PA1 to function as a general-purpose port if the debug function is not used.
Port Name
General-
purpose
PA0
PA1
PB0
PB1
PB2
PA2
PA3
PA4
PA5
PA6
Output
Output
Output
Output
Output
Output
Input
Input
Input
Input
I / O
JTAG Debug Function
JTAG Test Mode Selection
JTAG Test Data Output
JTAG Test Data Input
JTAG Test RESET
JTAG Test Check
Explanation
Page 22
TRACE DATA Output0
TRACE DATA Output1
TRACE DATA Output2
TRACE DATA Output3
TRACE Clock Output
(Output)(Note)
Input
I / O
I / O
-
-
SW Debug Function
Serial Wire Data Input/Output
TMPM333FDFG/FYFG/FWFG
(Serial Wire Viewer Output)
Serial Wire Clock
Explanation
-
-