TMP86xy48UG/FG Toshiba, TMP86xy48UG/FG Datasheet - Page 58

• Manufacturer Part Number: TMP86xy48UG/FG
• Manufacturer: Toshiba

Specifications of TMP86xy48UG/FG

• Package: LQFP64/QFP64
• Rom Types (m=mask,p=otp,f=flash): F/E
• Rom Size: 32
• Ram Size: 2K
• Driver Led: 11
• Driver Lcd: -
• Spi/sio Channels: 1
• Uart/sio Channels: 1
• I2c/sio Channels: 1
• High-speed Serial Output: 2
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 16
• Da Converter Channels: -
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 2
• Timer Counter 8-bit Channel: 2
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: -
• Number Of I/o Ports: 54
• Power Supply (v): 2.7 to 3.6

2.2.6
Data output (P6DR)
Data input (P6DR)
*: Don’t care.
*: Don’t care.
Note: STOPkEN is bit7 to 4 in STOPCR.
Port P6 (P67 to P60)
one-bit unit. Port P6 is also used as an analog input and key-on wake-up input.
Input/output mode is specified by the P6 control register (P6CR1). P6 port input is
controlled by the input control register (P6CR2).
P6CR1 is cleared to “0”.
“1”. (k = 3 to 0)
“1”. Table 2.2.1 and Table 2.2.2 show a P6 state.
STOPkEN
P6CR2i input
P6CR1i input
Analog input
Port P6 is an 8-bit input/output port which can be configured as an input or an output in
When used as an output port, respective P6CR1 should be set to “1”.
When used as an input port, respective P6CR1 should be cleared to “0” and respective
P6CR2 should be set to “1”.
When used as an analog input, respective P6CR2 should be cleared to “0” after respective
When used as a key on wake up input, respective STOPkEN<STOPCR> should be set to
During reset, the P6CR1 and P6DR are initialized to “0”, and the P6CR2 is initialized to
P6CR1
0
0
0
0
1
P6CR2i
P6CR1i
OUTEN
0
0
1
1
AINDS
STOP
SAIN
P6CR1
P6CR2
0
0
1
1
*
D
D
0
1
*
*
Q
Q
D
Figure 2.2.8 Port 6 (P63 to P60)
P6CR2
Table 2.2.1 P63 to P60 State
Table 2.2.2 P67 to P64 State
0
1
*
*
*
Q
P6DR
86FM48-54
*
*
0
1
P6DR
0
1
*
*
*
“0” (Output latch)
“1” (Output latch)
P6DR Read
Terminal input
“0” (Output latch)
“1” (Output latch)
Terminal input
Terminal input
P6DR read
“0”
“0”
Note 1: i = 3 to 0
Note 2: SAIN is bit0 to 3 in ADCCR1
P6i
Output
High-Z
High-Z
High
Output
Low
High-Z
High-Z
High-Z
High
Low
Output mode
Output mode
Key on wake up
Input mode
Remark
Output mode
Output mode
Input mode
Remark
TMP86FM48
−
2007-08-24
−