MC56F8245VLD Freescale Semiconductor, MC56F8245VLD Datasheet - Page 345

• Manufacturer Part Number: MC56F8245VLD
• Description: DSC 48K FLASH 60MHZ 44-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8245VLD

• Core Processor: 56800E
• Core Size: 16-Bit
• Speed: 60MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 48KB (24K x 16)
• Program Memory Type: FLASH
• Ram Size: 3K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 44-LQFP
• Product: DSCs
• Processor Series: 56800E
• Core: 56800E
• Device Million Instructions Per Second: 60 MIPs
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 35
• Data Ram Size: 6 KB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 4 Channel
• Package: 44LQFP
• Family Name: MC56F82xx
• Maximum Speed: 60 MHz
• Data Bus Width: 16 Bit
• Interface Type: I2C/SCI/SPI
• On-chip Dac: 1-chx12-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

10.4.6.4 Arbitration Lost Interrupt
The I2C is a true multimaster bus that allows more than one master to be connected on it.
If two or more masters try to control the bus at the same time, the relative priority of the
contending masters is determined by a data arbitration procedure. The I2C module asserts
the arbitration-lost interrupt when it loses the data arbitration process and the ARBL bit
in the Status Register is set.
Arbitration is lost in the following circumstances:
The ARBL bit must be cleared (by software) by writing 1 to it.
10.4.6.5 Timeout Interrupt in SMBus
When the IICIE bit is set, the I2C module asserts a timeout interrupt (outputs SLTF and
SHTF2) upon detection of any of the mentioned timeout conditions, with one exception.
The SCL high and SDA high TIMEOUT mechanism must not be used to influence the
timeout interrupt output, because this timeout indicates an idle condition on the bus.
SHTF1 rises when it matches the SCL high and SDA high TIMEOUT and falls
automatically just to indicate the bus status. The SHTF2's timeout period is the same as
that of SHTF1, which is short compared to that of SLTF, so another control bit,
SHTF2IE, is added to enable or disable it.
10.4.6.6 Programmable Input Glitch Filter
An I2C glitch filter has been added outside legacy I2C modules but within the I2C
package. This filter can absorb glitches on the I2C clock and data lines for the I2C
module. The width of the glitch to absorb can be specified in terms of the number of
(half) bus clock cycles. A single Programmable Input Glitch Filter control register is
Freescale Semiconductor
1. SDA is sampled as low when the master drives high during an address or data
2. SDA is sampled as low when the master drives high during the acknowledge bit of a
3. A START cycle is attempted when the bus is busy.
4. A repeated START cycle is requested in slave mode.
5. A STOP condition is detected when the master did not request it.
transmit cycle.
data receive cycle.
MC56F825x/4x Reference Manual, Rev. 2, 10/2010
Preliminary
Chapter 10 Inter-Integrated Circuit (I2C)
345