DSPIC33FJ16MC101T-I/SS Microchip Technology, DSPIC33FJ16MC101T-I/SS Datasheet - Page 122

• Manufacturer Part Number: DSPIC33FJ16MC101T-I/SS
• Description: 16-bit Motor Control DSC Family, 16 MIPS, 16KB Flash, 1KB RAM 20 SSOP .209in T/R
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16MC101T-I/SS

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 16 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SSOP (0.209", 5.30mm Width)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

dsPIC33FJ16GP101/102 AND dsPIC33FJ16MC101/102
10.1.1
In addition to the PORT, LAT, and TRIS registers for
data control, some port pins can also be individually
configured for either digital or open-drain output. This
is controlled by the Open-Drain Control register,
ODCx, associated with each port. Setting any of the
bits configures the corresponding pin to act as an
open-drain output.
The open-drain feature allows the generation of
outputs higher than V
tolerant pins by using external pull-up resistors. The
maximum open-drain voltage allowed is the same as
the maximum V
See
functionality.
10.2
The AD1PCFG and TRIS registers control the opera-
tion of the analog-to-digital port pins. The port pins that
are to function as analog inputs must have their corre-
sponding TRIS bit set (input). If the TRIS bit is cleared
(output), the digital output level (V
converted.
The AD1PCFGL register has a default value of 0x0000;
therefore, all pins that share ANx functions are analog
(not digital) by default.
When the PORT register is read, all pins configured as
analog input channels will read as cleared (a low level).
Pins configured as digital inputs will not convert an
analog input. Analog levels on any pin defined as a
digital input (including the ANx pins) can cause the
input buffer to consume current that exceeds the
device specifications.
10.2.1
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically this instruction
would be an NOP. An demonstration is shown in
Example
EXAMPLE 10-1:
DS70652C-page 122
MOV
MOV
NOP
btss
“Pin
0xFF00, W0
W0, TRISBB
PORTB, #13
Configuring Analog Port Pins
10-1.
Diagrams” for the available pins and their
OPEN-DRAIN CONFIGURATION
I/O PORT WRITE/READ TIMING
IH
specification.
DD
PORT WRITE/READ EXAMPLE
(e.g., 5V) on any desired 5V
; Configure PORTB<15:8> as inputs
; and PORTB<7:0> as outputs
; Delay 1 cycle
; Next Instruction
OH
or V
OL
) will be
Preliminary
10.3
The input change notification function of the I/O ports
allows
dsPIC33FJ16MC101/102 devices to generate interrupt
requests to the processor in response to a change-of-
state on selected input pins. This feature can detect
input change-of-states even in Sleep mode, when the
clocks are disabled. Depending on the device pin
count, up to 21 external signals (CNx pin) can be
selected (enabled) for generating an interrupt request
on a change-of-state.
Four control registers are associated with the CN mod-
ule. The CNEN1 and CNEN2 registers contain the
interrupt enable control bits for each of the CN input
pins. Setting any of these bits enables a CN interrupt
for the corresponding pins.
Each CN pin also has a weak pull-up connected to it.
The pull-ups act as a current source connected to the
pin, and eliminate the need for external resistors when
push-button or keypad devices are connected. The
pull-ups are enabled separately using the CNPU1 and
CNPU2 registers, which contain the control bits for
each of the CN pins. Setting any of the control bits
enables the weak pull-ups for the corresponding pins.
Note:
Input Change Notification
the
Pull-ups on change notification pins
should always be disabled when the port
pin is configured as a digital output.
dsPIC33FJ16GP101/102
© 2011 Microchip Technology Inc.
and