DSPIC33FJ16MC101T-I/SS Microchip Technology, DSPIC33FJ16MC101T-I/SS Datasheet - Page 21

• Manufacturer Part Number: DSPIC33FJ16MC101T-I/SS
• Description: 16-bit Motor Control DSC Family, 16 MIPS, 16KB Flash, 1KB RAM 20 SSOP .209in T/R
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16MC101T-I/SS

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 16 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SSOP (0.209", 5.30mm Width)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.0
2.1
Getting started with the dsPIC33FJ16GP101/102 and
dsPIC33FJ16MC101/102 family of 16-bit Digital Signal
Controllers (DSCs) requires attention to a minimal set
of device pin connections before proceeding with
development. The following is a list of pin names, which
must always be connected:
• All V
• All AV
• V
• MCLR pin
• PGECx/PGEDx pins used for In-Circuit Serial
• OSC1 and OSC2 pins when external oscillator
© 2011 Microchip Technology Inc.
(see
(regardless if ADC module is not used)
(see
(see
Connection (V
(see
Programming™ (ICSP™) and debugging purposes
(see
source is used
(see
dsPIC33FJ16GP101/102 AND dsPIC33FJ16MC101/102
Note 1: This data sheet summarizes the features
CAP
DD
Section 2.2 “Decoupling
Section 2.2 “Decoupling
Section 2.3 “CPU Logic Filter Capacitor
Section 2.4 “Master Clear (MCLR)
Section 2.5 “ICSP
Section 2.6 “External Oscillator
DD
2: Some registers and associated bits
GUIDELINES FOR GETTING
STARTED WITH 16-BIT
DIGITAL SIGNAL
CONTROLLERS
Basic Connection Requirements
and V
and AV
of the dsPIC33FJ16GP101/102 and
dsPIC33FJ16MC101/102
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to the “dsPIC33F/PIC24H
Family Reference Manual”. Please see
the
(www.microchip.com)
dsPIC33F/PIC24H
Manual sections.
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization”
this data sheet for device-specific register
and bit information.
SS
CAP
SS
pins
)”)
pins, if present on the device
Microchip
Pins”)
Family
Capacitors”)
Capacitors”)
for
web
Pins”)
family
the
Reference
Pin”)
latest
site
Preliminary
of
in
2.2
The use of decoupling capacitors on every pair of
power supply pins, such as V
AV
Consider the following criteria when using decoupling
capacitors:
• Value and type of capacitor: Recommendation
• Placement on the printed circuit board: The
• Handling high frequency noise: If the board is
• Maximizing performance: On the board layout
of 0.1 µF (100 nF), 10V – 20V. This capacitor
should be a low-ESR and have resonance
frequency in the range of 20 MHz and higher. It is
recommended that ceramic capacitors be used.
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is within
one-quarter inch (6 mm) in length.
experiencing high frequency noise, upward of
tens of MHz, add a second ceramic-type capacitor
in parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01 µF to 0.001 µF. Place this
second capacitor next to the primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible.
For example, 0.1 µF in parallel with 0.001 µF.
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum thereby reducing PCB track inductance.
SS
is required.
Decoupling Capacitors
DD
, V
DS70652C-page 21
SS
, AV
DD
, and