DSPIC33FJ16MC101T-I/SS Microchip Technology, DSPIC33FJ16MC101T-I/SS Datasheet - Page 70

• Manufacturer Part Number: DSPIC33FJ16MC101T-I/SS
• Description: 16-bit Motor Control DSC Family, 16 MIPS, 16KB Flash, 1KB RAM 20 SSOP .209in T/R
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16MC101T-I/SS

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 16 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SSOP (0.209", 5.30mm Width)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

dsPIC33FJ16GP101/102 AND dsPIC33FJ16MC101/102
REGISTER 6-1:
DS70652C-page 70
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
Note 1:
TRAPR
R/W-0
R/W-0
EXTR
2:
All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an
0 = An illegal opcode or uninitialized W Reset has not occurred
Unimplemented: Read as ‘0’
CM: Configuration Mismatch Flag bit
1 = A configuration mismatch Reset has occurred
0 = A configuration mismatch Reset has NOT occurred
VREGS: Voltage Regulator Stand-by During Sleep bit
1 = Voltage regulator is active during Sleep
0 = Voltage regulator goes into Stand-by mode during Sleep
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
SLEEP: Wake-up from Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
IDLE: Wake-up from Idle Flag bit
1 = Device was in Idle mode
0 = Device was not in Idle mode
IOPUWR
R/W-0
R/W-0
SWR
Address Pointer caused a Reset
RCON: RESET CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0
U-0
—
(2)
WDTO
R/W-0
U-0
Preliminary
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SLEEP
R/W-0
(2)
U-0
—
(1)
R/W-0
IDLE
U-0
—
© 2011 Microchip Technology Inc.
x = Bit is unknown
R/W-0
R/W-1
BOR
CM
VREGS
R/W-0
R/W-1
POR
bit 8
bit 0