PIC16F1829-E/P Microchip Technology, PIC16F1829-E/P Datasheet - Page 266

• Manufacturer Part Number: PIC16F1829-E/P
• Description: 14 KB Flash, 1K Bytes RAM, 32 MHz Int. Osc, 18 I/0, Enhanced Mid Range Core 20 P
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ mTouch™ 16Fr

Specifications of PIC16F1829-E/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: *
• Processor Series: PIC16F182x
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16F/LF1825/1829
25.5.3.3
Setting the AHEN bit of the SSPxCON3 register
enables additional clock stretching and interrupt gen-
eration after the 8th falling edge of a received match-
ing address. Once a matching address has been
clocked in, CKP is cleared and the SSPxIF interrupt is
set.
Figure 25-18
Address Slave Transmission with AHEN enabled.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Slave hardware automatically clears the CKP bit
11. Slave software clears SSPxIF.
12. Slave loads value to transmit to the master into
13. Slave sets CKP bit releasing the clock.
14. Master clocks out the data from the slave and
15. Slave hardware copies the ACK value into the
16. Steps 10-15 are repeated for each byte transmit-
17. If the master sends a not ACK the slave
DS41440A-page 268
Note: SSPxBUF cannot be loaded until after the
Note: Master must send a not ACK on the last byte
Bus starts Idle.
Master sends Start condition; the S bit of
SSPxSTAT is set; SSPxIF is set if interrupt on
Start detect is enabled.
Master sends matching address with R/W bit
set. After the 8th falling edge of the SCLx line the
CKP bit is cleared and SSPxIF interrupt is
generated.
Slave software clears SSPxIF.
Slave software reads ACKTIM bit of SSPxCON3
register, and R/W and D/A of the SSPxSTAT
register to determine the source of the interrupt.
Slave reads the address value from the
SSPxBUF register clearing the BF bit.
Slave software decides from this information if it
wishes to ACK or not ACK and sets the ACKDT
bit of the SSPxCON2 register accordingly.
Slave sets the CKP bit releasing SCLx.
Master clocks in the ACK value from the slave.
and sets SSPxIF after the ACK if the R/W bit is
set.
SSPxBUF setting the BF bit.
sends an ACK value on the 9th SCLx pulse.
ACKSTAT bit of the SSPxCON2 register.
ted to the master from the slave.
releases the bus allowing the master to send a
Stop and end the communication.
ACK.
to ensure that the slave releases the SCLx
line to receive a Stop.
7-bit Transmission with Address
Hold Enabled
displays a standard waveform of a 7-bit
Preliminary
 2010 Microchip Technology Inc.