gwixp465bad ETC-unknow, gwixp465bad Datasheet - Page 75

• Manufacturer Part Number: gwixp465bad
• Description: Network Proc 1.3v/1.4v/2.5v/3.3v 400mhz 544-pin Bga
• Manufacturer: ETC-unknow

Package Information
Table 24.
Table 25.
August 2006
75
PLL_LOCK
RCOMP_REF
SPARE1
SPARE2
Note:
†
V
V
V
V
OSC_VCCP
OSC_VSSP
OSC_VCC
Note:
†
CC
CCP
CCM
SS
Name
Name
This table discusses all features supported on the Intel
see
For a legend of the Type codes, see
This table discusses all features supported on the Intel
see
For a legend of the Type codes, see
Table 1 on page
Table 1 on page
System Interface (Sheet 2 of 2)
Power Interface (Sheet 1 of 2)
Power
Reset
N/A
N/A
N/A
N/A
N/A
N/A
N/A
on
†
Tied off
resistor
Power
Reset
to a
n/a
n/a
on
13.
13.
0
Reset
N/A
N/A
N/A
N/A
N/A
N/A
N/A
†
†
Reset
Tied off
resistor
to a
n/a
n/a
VO
Software
Enables
Normal
†
Reset
After
Until
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Table 8 on page
Table 8 on page
Software
Tied off to
a resistor
Enables
Normal
Reset
After
Until
n/a
n/a
VO
Software
Configur
Possible
Enables
ations
After
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Software
Tied off to
Configur
Possible
a resistor
Enables
ations
43.
43.
After
®
®
n/a
n/a
VO
IXP45X and Intel
IXP45X and Intel
Type
I
I
I
I
I
I
I
†
Type
n/a
n/a
O
O
1.3-V power supply input pins used for the internal logic. If operating at 667 MHz, this supply voltage
needs to be increased to VCC = 1.5 V.
3.3-V power supply input pins used for the peripheral (I/O) logic.
2.5-V power supply input pins used for the DDR memory interface
Ground power supply input pins used for both the 3.3-V, 2.5-V, and the 1.3-V power supplies.
3.3-V power supply input pins used for the peripheral (I/O) logic of the analog oscillator circuitry.
Require special power filtering circuitry. Refer to
Ground input pins used for the peripheral (I/O) logic of the analog oscillator circuitry. Used in
conjunction with the OSC_VCCP pins.
Requires special power filtering circuitry. Refer to
1.3-V power supply input pins used for the internal logic of the analog oscillator circuitry. Requires
special power filtering circuitry. If operating at 667 MHz, this supply voltage needs to be increased to
VCC = 1.5 V. Refer to
†
®
Signal used to inform external reset logic that the internal PLL has achieved a locked state.
PLL_LOCK will also be de-asserted during a watchdog timeout.
Signal used to control PCI and SMII drive strength characteristics. Drive strength is varied on
PCI and SMII signals depending upon temperature.
Pin requires a 34-Ω +/- 1% tolerance resistor to ground. (Refer to
No Connection is to be made to this signal
No Connection is to be made to this signal
®
IXP46X Product Line of Network Processors. For details on feature support listed by processor,
IXP46X Product Line of Network Processors. For details on feature support listed by processor,
Figure 13 on page
Intel
®
IXP45X and Intel
106.
Description
®
Description
IXP46X Product Line of Network Processors Datasheet
Figure 12 on page
Figure 12 on page
Document Number:
106.
106.
Figure 14 on page
306261-004US
107.)