ATMEGA16A-PU Atmel, ATMEGA16A-PU Datasheet - Page 39

MCU AVR 16K FLASH 16MHZ 40-PDIP

ATMEGA16A-PU

Manufacturer Part Number
ATMEGA16A-PU
Description
MCU AVR 16K FLASH 16MHZ 40-PDIP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets

Specifications of ATMEGA16A-PU

Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Processor Series
ATMEGA16x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
1 KB
Interface Type
2-Wire/SPI/USART
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
32
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
Package
40PDIP
Device Core
AVR
Family Name
ATmega
Maximum Speed
16 MHz
Operating Supply Voltage
3.3|5 V
Controller Family/series
AVR MEGA
No. Of I/o's
32
Eeprom Memory Size
512Byte
Ram Memory Size
1KB
Cpu Speed
16MHz
Rohs Compliant
Yes
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
10.1.3
10.1.4
8154B–AVR–07/09
External Reset
Brown-out Detection
Figure 10-3. MCU Start-up, RESET Extended Externally
An External Reset is generated by a low level on the RESET pin. Reset pulses longer than the
minimum pulse width (see
reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset.
When the applied signal reaches the Reset Threshold Voltage – V
delay counter starts the MCU after the Time-out period t
Figure 10-4. External Reset During Operation
ATmega16A has an On-chip Brown-out Detection (BOD) circuit for monitoring the V
ing operation by comparing it to a fixed trigger level. The trigger level for the BOD can be
selected by the fuse BODLEVEL to be 2.7V (BODLEVEL unprogrammed), or 4.0V (BODLEVEL
programmed). The trigger level has a hysteresis to ensure spike free Brown-out Detection. The
hysteresis on the detection level should be interpreted as V
V
The BOD circuit can be enabled/disabled by the fuse BODEN. When the BOD is enabled
(BODEN programmed), and V
5), the Brown-out Reset is immediately activated. When V
(V
expired.
The BOD circuit will only detect a drop in V
ger than t
BOT
BOT+
- V
in
INTERNAL
TIME-OUT
HYST
BOD
Figure
RESET
RESET
V
/2.
CC
given in
CC
10-5), the delay counter starts the MCU after the Time-out period t
“System and Reset Characteristics” on page
“System and Reset Characteristics” on page
V
CC
POT
decreases to a value below the trigger level (V
CC
if the voltage stays below the trigger level for lon-
V
RST
t
TOUT
TOUT
CC
has expired.
BOT+
increases above the trigger level
= V
RST
296.
BOT
– on its positive edge, the
ATmega16A
+ V
296) will generate a
HYST
BOT-
/2 and V
in
CC
Figure 10-
level dur-
TOUT
BOT-
has
39
=

Related parts for ATMEGA16A-PU