ATMEGA16A-PU Atmel, ATMEGA16A-PU Datasheet - Page 90
Manufacturer Part Number
MCU AVR 16K FLASH 16MHZ 40-PDIP
1.ATMEGA16A-MU.pdf (352 pages)
2.ATMEGA16A-MU.pdf (19 pages)
Specifications of ATMEGA16A-PU
I²C, SPI, UART/USART
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
Program Memory Size
16KB (8K x 16)
Program Memory Type
512 x 8
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Data Bus Width
Data Ram Size
Maximum Clock Frequency
Number Of Programmable I/os
Number Of Timers
Maximum Operating Temperature
+ 85 C
3rd Party Development Tools
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
8-ch x 10-bit
Operating Supply Voltage
No. Of I/o's
Eeprom Memory Size
Ram Memory Size
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
put Compare Units” on page 97.
Flag (OCF1A/B) which can be used to generate an output compare interrupt request.
The Input Capture Register can capture the Timer/Counter value at a given external (edge trig-
gered) event on either the Input Capture Pin (ICP1) or on the Analog Comparator pins
“Analog Comparator” on page
Canceler) for reducing the chance of capturing noise spikes.
The TOP value, or maximum Timer/Counter value, can in some modes of operation be defined
by either the OCR1A Register, the ICR1 Register, or by a set of fixed values. When using
OCR1A as TOP value in a PWM mode, the OCR1A Register can not be used for generating a
PWM output. However, the TOP value will in this case be double buffered allowing the TOP
value to be changed in run time. If a fixed TOP value is required, the ICR1 Register can be used
as an alternative, freeing the OCR1A to be used as PWM output.
The following definitions are used extensively throughout the document:
The 16-bit Timer/Counter has been updated and improved from previous versions of the 16-bit
AVR Timer/Counter. This 16-bit Timer/Counter is fully compatible with the earlier version
The following control bits have changed name, but have same functionality and register location:
The following bits are added to the 16-bit Timer/Counter Control Registers:
The 16-bit Timer/Counter has improvements that will affect the compatibility in some special
• All 16-bit Timer/Counter related I/O Register address locations, including Timer Interrupt
• Bit locations inside all 16-bit Timer/Counter Registers, including Timer Interrupt Registers.
• Interrupt Vectors.
• PWM10 is changed to WGM10.
• PWM11 is changed to WGM11.
• CTC1 is changed to WGM12.
• FOC1A and FOC1B are added to TCCR1A.
• WGM13 is added to TCCR1B.
The counter reaches the BOTTOM when it becomes 0x0000.
The counter reaches its MAXimum when it becomes 0xFFFF (decimal 65535).
The counter reaches the TOP when it becomes equal to the highest value in the count
sequence. The TOP value can be assigned to be one of the fixed values: 0x00FF,
0x01FF, or 0x03FF, or to the value stored in the OCR1A or ICR1 Register. The assign-
ment is dependent of the mode of operation.
204.) The Input Capture unit includes a digital filtering unit (Noise
The compare match event will also set the Compare Match