M30802FCGP#D3 Renesas Electronics America, M30802FCGP#D3 Datasheet - Page 171

IC M16C MCU FLASH 128K 144LQFP

M30802FCGP#D3

Manufacturer Part Number
M30802FCGP#D3
Description
IC M16C MCU FLASH 128K 144LQFP
Manufacturer
Renesas Electronics America
Series
M16C™ M16C/80r
Datasheet

Specifications of M30802FCGP#D3

Core Processor
M16C/80
Core Size
16-Bit
Speed
20MHz
Connectivity
SIO, UART/USART
Peripherals
DMA, PWM, WDT
Number Of I /o
121
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
10K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 10x10b, D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M30802FCGP#D3M30802FCGP
Manufacturer:
MITSHBISHI
Quantity:
20 000
Company:
Part Number:
M30802FCGP#D3M30802FCGP
Quantity:
81
Company:
Part Number:
M30802FCGP#D3M30802FCGP D5
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
M
R
R
e
E
1
v
J
6
1 .
0
C
9
0 .
8 /
B
0
0
0
1
A
The start condition detection interrupt is generated when the fall at the SDA2 pin (P7
while the SCL2 pin (P7
rise at the SDA2 pin (P7
The acknowledge non-detection interrupt is generated when the H level at the SDA2 pin is detected at
the 9th rise of the transmission clock.
The acknowledge detection interrupt is generated when the L level at the SDA2 pin is detected at the
9th rise of the transmission clock. Also, DMA transfer can be started when the acknowledge is de-
tected if UART2 transmission is selected as the DMAi request factor.
Bit 2 is the bus busy flag. It is set to “1” when the start condition is detected, and reset to “0” when the
stop condition is detected.
Bit 1 is the arbitration lost detection flag control bit. Arbitration detects a conflict between data trans-
mitted at SCL2 rise and data at the SDA2 pin. This detection flag is allocated to bit 11 in UART2
transmission buffer register (address 033E
arbitration lost detection flag control bit, it can be selected to update the flag in units of bits or bytes.
When this bit is set to “1”, update is set to units of byte. If a conflict is then detected, the arbitration lost
detection flag control bit will be set to “1” at the 9th rise of the clock. When updating in units of byte,
always clear (“0” interrupt) the arbitration lost detection flag control bit after the 1st byte has been
acknowledged but before the next byte starts transmitting.
Bit 3 is the SCL2 L synchronization output enable bit. When this bit is set to “1”, the P7
is set to “0” in sync with the L level at the SCL2 pin.
Bit 4 is the bus collision detection sampling clock select bit. The bus collision detection interrupt is
generated when RxDi and TxDi level do not conflict with one another. When this bit is “0”, a conflict is
detected in sync with the rise of the transfer clock. When this bit is “1”, detection is made when timer
Ai (timer A0 with UART2, timer A3 with UART3 and timer A4 with UART4) underflows. Operation is
shown in Figure 20.3.
Bit 5 is the transmission enable bit automatic clear select bit. By setting this bit to “1”, the transmission
bit is automatically reset to “0” when the bus collision detection interrupt factor bit is “1” (when a conflict
is detected).
Bit 6 is the transmission start condition select bit. By setting this bit to “1”, TxDi transmission starts in
sync with the falling at the RxDi pin.
8
G
u
7
o r
. g
0 -
u
1
0
p
0
, 2
0
2
0
0
5
Page 158
1
) is in the H state. The stop condition detection interrupt is generated when the
0
f o
) is detected while the SCL2 pin (P7
3
2
9
16
). It is set to “1” when a conflict is detected. With the
20. UARTi Special Mode Register (i = 2 to 4)
1
) is in the H state.
1
0
) is detected
data register

Related parts for M30802FCGP#D3