M30802FCGP#D3 Renesas Electronics America, M30802FCGP#D3 Datasheet - Page 287

IC M16C MCU FLASH 128K 144LQFP

M30802FCGP#D3

Manufacturer Part Number
M30802FCGP#D3
Description
IC M16C MCU FLASH 128K 144LQFP
Manufacturer
Renesas Electronics America
Series
M16C™ M16C/80r
Datasheet

Specifications of M30802FCGP#D3

Core Processor
M16C/80
Core Size
16-Bit
Speed
20MHz
Connectivity
SIO, UART/USART
Peripherals
DMA, PWM, WDT
Number Of I /o
121
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
10K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 10x10b, D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M30802FCGP#D3M30802FCGP
Manufacturer:
MITSHBISHI
Quantity:
20 000
Company:
Part Number:
M30802FCGP#D3M30802FCGP
Quantity:
81
Company:
Part Number:
M30802FCGP#D3M30802FCGP D5
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
M
R
R
30. CPU Rewrite Mode
e
E
1
v
J
6
1 .
0
C
In CPU rewrite mode, the on-chip flash memory can be operated on (read, program, or erase) under control
of the Central Processing Unit (CPU).
In CPU rewrite mode, only the user ROM area shown in Figure 29.3 can be rewritten; the boot ROM area
cannot be rewritten. Make sure the program and block erase commands are issued for only the user ROM
area and each block area.
The control program for CPU rewrite mode can be stored in either user ROM or boot ROM area. In the CPU
rewrite mode, because the flash memory cannot be read from the CPU, the rewrite control program must
be transferred to any area other than the internal flash memory before it can be executed.
Microcomputer Mode and Boot Mode
Block Address
9
0 .
8 /
B
The control program for CPU rewrite mode must be written into the user ROM or boot ROM area in
parallel I/O mode beforehand. (If the control program is written into the boot ROM area, the standard
serial I/O mode becomes unusable.)
See Figure 29.3 for details about the boot ROM area.
Normal microcomputer mode is entered when the microcomputer is reset with pulling CNV
this case, the CPU starts operating using the control program in the user ROM area.
When the microcomputer is reset by pulling the P5
CPU starts operating using the control program in the boot ROM area. This mode is called the “boot”
mode. The control program in the boot ROM area can also be used to rewrite the user ROM area.
Block addresses refer to the maximum even address of each block. These addresses are used in the
block erase command, lock bit program command, and read lock status command.
0
0
0
1
A
8
G
u
7
o r
. g
0 -
u
1
0
p
0
, 2
0
2
0
0
5
Page 274
f o
3
2
9
5
pin low, the CNV
SS
pin high, and the P5
30. CPU Rewrite Mode
0
SS
pin high, the
pin low. In

Related parts for M30802FCGP#D3