MC68HC908MR16CFU Freescale Semiconductor, MC68HC908MR16CFU Datasheet - Page 163

• Manufacturer Part Number: MC68HC908MR16CFU
• Description: IC MCU 8MHZ 16K FLASH 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908MR16CFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 44
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

13.3.2.4 Idle Characters
An idle character contains all 1s and has no start, stop, or parity bit. Idle character length depends on the
M bit in SCC1. The preamble is a synchronizing idle character that begins every transmission.
If the TE bit is cleared during a transmission, the PTF5/TxD pin becomes idle after completion of the
transmission in progress. Clearing and then setting the TE bit during a transmission queues an idle
character to be sent after the character currently being transmitted.
13.3.2.5 Inversion of Transmitted Output
The transmit inversion bit (TXINV) in SCI control register 1 (SCC1) reverses the polarity of transmitted
data. All transmitted values, including idle, break, start, and stop bits, are inverted when TXINV is at 1.
See
13.3.2.6 Transmitter Interrupts
These conditions can generate CPU interrupt requests from the SCI transmitter:
13.3.3 Receiver
Figure 13-6
Freescale Semiconductor
•
•
13.7.1 SCI Control Register
SCI transmitter empty (SCTE) — The SCTE bit in SCS1 indicates that the SCDR has transferred
a character to the transmit shift register. SCTE can generate a transmitter CPU interrupt request.
Setting the SCI transmit interrupt enable bit, SCTIE, in SCC2 enables the SCTE bit to generate
transmitter CPU interrupt requests.
Transmission complete (TC) — The TC bit in SCS1 indicates that the transmit shift register and the
SCDR are empty and that no break or idle character has been generated. The transmission
complete interrupt enable bit, TCIE, in SCC2 enables the TC bit to generate transmitter CPU
interrupt requests.
shows the structure of the SCI receiver.
When a break sequence is followed immediately by an idle character, this
SCI design exhibits a condition in which the break character length is
reduced by one half bit time. In this instance, the break sequence will
consist of a valid start bit, eight or nine data bits (as defined by the M bit in
SCC1) of logic 0 and one half data bit length of logic 0 in the stop bit position
followed immediately by the idle character. To ensure a break character of
the proper length is transmitted, always queue up a byte of data to be
transmitted while the final break sequence is in progress.
When queueing an idle character, return the TE bit to 1 before the stop bit
of the current character shifts out to the PTF5/TxD pin. Setting TE after the
stop bit appears on PTF5/TxD causes data previously written to the SCDR
to be lost.
A good time to toggle the TE bit is when the SCTE bit becomes set and just
before writing the next byte to the SCDR.
MC68HC908MR32 • MC68HC908MR16 Data Sheet, Rev. 6.1
1.
NOTE
Functional Description
163