MC68HC908MR16CFU Freescale Semiconductor, MC68HC908MR16CFU Datasheet - Page 59

• Manufacturer Part Number: MC68HC908MR16CFU
• Description: IC MCU 8MHZ 16K FLASH 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908MR16CFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 44
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

4.3.1 Crystal Oscillator Circuit
The crystal oscillator circuit consists of an inverting amplifier and an external crystal. The OSC1 pin is the
input to the amplifier and the OSC2 pin is the output. The SIMOSCEN signal from the system integration
module (SIM) enables the crystal oscillator circuit.
The CGMXCLK signal is the output of the crystal oscillator circuit and runs at a rate equal to the crystal
frequency. CGMXCLK is then buffered to produce CGMRCLK, the PLL reference clock.
CGMXCLK can be used by other modules which require precise timing for operation. The duty cycle of
CGMXCLK is not guaranteed to be 50 percent and depends on external factors, including the crystal and
related external components.
An externally generated clock also can feed the OSC1 pin of the crystal oscillator circuit. Connect the
external clock to the OSC1 pin and let the OSC2 pin float.
4.3.2 Phase-Locked Loop Circuit (PLL)
The PLL is a frequency generator that can operate in either acquisition mode or tracking mode, depending
on the accuracy of the output frequency. The PLL can change between acquisition and tracking modes
either automatically or manually.
4.3.2.1 PLL Circuits
The PLL consists of these circuits:
The operating range of the VCO is programmable for a wide range of frequencies and for maximum
immunity to external noise, including supply and CGMXFC noise. The VCO frequency is bound to a range
from roughly one-half to twice the center-of-range frequency, f
CGMXFC pin changes the frequency within this range. By design, f
center-of-range frequency, f
CGMRCLK is the PLL reference clock, a buffered version of CGMXCLK. CGMRCLK runs at a frequency,
f
running at a frequency, f
The VCO’s output clock, CGMVCLK, running at a frequency, f
modulo divider. The modulo divider reduces the VCO clock by a factor, N. The divider’s output is the VCO
feedback clock, CGMVDV, running at a frequency, f
more information.)
The phase detector then compares the VCO feedback clock, CGMVDV, with the final reference clock,
CGMRDV. A correction pulse is generated based on the phase difference between the two signals. The
loop filter then slightly alters the dc voltage on the external capacitor connected to CGMXFC based on
the width and direction of the correction pulse. The filter can make fast or slow corrections depending on
its mode, described in
the reference frequency determines the speed of the corrections and the stability of the PLL.
Freescale Semiconductor
RCLK
•
•
•
•
•
, and is fed to the PLL through a buffer. The buffer output is the final reference clock, CGMRDV,
Voltage-controlled oscillator (VCO)
Modulo VCO frequency divider
Phase detector
Loop filter
Lock detector
4.3.2.2 Acquisition and Tracking
RDV
MC68HC908MR32 • MC68HC908MR16 Data Sheet, Rev. 6.1
NOM
= f
RCLK
, (4.9152 MHz) times a linear factor, L or (L) f
.
VDV
= f
Modes. The value of the external capacitor and
VCLK/N
VCLK
VRS
. (See
. Modulating the voltage on the
, is fed back through a programmable
VRS
4.3.2.4 Programming the PLL
is equal to the nominal
NOM
.
Functional Description
for
59