MC68HC908MR16CFU Freescale Semiconductor, MC68HC908MR16CFU Datasheet - Page 176

• Manufacturer Part Number: MC68HC908MR16CFU
• Description: IC MCU 8MHZ 16K FLASH 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908MR16CFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 44
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Serial Communications Interface Module (SCI)
NF — Receiver Noise Flag Bit
FE — Receiver Framing Error Bit
PE — Receiver Parity Error Bit
13.7.5 SCI Status Register 2
SCI status register 2 (SCS2) contains flags to signal these conditions:
BKF — Break Flag
176
In applications that are subject to software latency or in which it is important to know which byte is lost
due to an overrun, the flag-clearing routine can check the OR bit in a second read of SCS1 after
reading the data register.
This clearable, read-only bit is set when the SCI detects noise on the PTF4/RxD pin. NF generates an
NF CPU interrupt request if the NEIE bit in SCC3 is also set. Clear the NF bit by reading SCS1 and
then reading the SCDR. Reset clears the NF bit.
This clearable, read-only bit is set when a 0 is accepted as the stop bit. FE generates an SCI error CPU
interrupt request if the FEIE bit in SCC3 also is set. Clear the FE bit by reading SCS1 with FE set and
then reading the SCDR. Reset clears the FE bit.
This clearable, read-only bit is set when the SCI detects a parity error in incoming data. PE generates
a PE CPU interrupt request if the PEIE bit in SCC3 is also set. Clear the PE bit by reading SCS1 with
PE set and then reading the SCDR. Reset clears the PE bit.
•
•
This clearable, read-only bit is set when the SCI detects a break character on the PTF4/RxD pin. In
SCS1, the FE and SCRF bits are also set. In 9-bit character transmissions, the R8 bit in SCC3 is
cleared. BKF does not generate a CPU interrupt request. Clear BKF by reading SCS2 with BKF set
and then reading the SCDR. Once cleared, BKF can become set again only after logic 1s again appear
on the PTF4/RxD pin followed by another break character. Reset clears the BKF bit.
1 = Noise detected
0 = No noise detected
1 = Framing error detected
0 = No framing error detected
1 = Parity error detected
0 = No parity error detected
1 = Break character detected
0 = No break character detected
Break character detected
Incoming data
Address:
Reset:
Read:
Write:
$003C
Bit 7
R
R
0
0
MC68HC908MR32 • MC68HC908MR16 Data Sheet, Rev. 6.1
Figure 13-13. SCI Status Register 2 (SCS2)
= Reserved
R
6
0
0
R
5
0
0
R
4
0
0
R
3
0
0
R
2
0
0
BKF
R
1
0
Freescale Semiconductor
Bit 0
RPF
R
0