MC68HC908MR16CFU Freescale Semiconductor, MC68HC908MR16CFU Datasheet - Page 69

• Manufacturer Part Number: MC68HC908MR16CFU
• Description: IC MCU 8MHZ 16K FLASH 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908MR16CFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 44
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

VRS[7:4] — VCO Range Select Bits
4.6 Interrupts
When the AUTO bit is set in the PLL bandwidth control register (PBWC), the PLL can generate a CPU
interrupt request every time the LOCK bit changes state. The PLLIE bit in the PLL control register (PCTL)
enables CPU interrupts from the PLL. PLLF, the interrupt flag in the PCTL, becomes set whether
interrupts are enabled or not. When the AUTO bit is clear, CPU interrupts from the PLL are disabled and
PLLF reads as logic 0.
Software should read the LOCK bit after a PLL interrupt request to see if the request was due to an entry
into lock or an exit from lock. When the PLL enters lock, the VCO clock, CGMVCLK, divided by two can
be selected as the CGMOUT source by setting BCS in the PCTL. When the PLL exits lock, the VCO clock
frequency is corrupt, and appropriate precautions should be taken. If the application is not
frequency-sensitive, interrupts should be disabled to prevent PLL interrupt service routines from impeding
software performance or from exceeding stack limitations.
4.7 Wait Mode
The WAIT instruction puts the MCU in low power-consumption standby mode.
The WAIT instruction does not affect the CGM. Before entering wait mode, software can disengage and
turn off the PLL by clearing the BCS and PLLON bits in the PLL control register (PCTL). Less
power-sensitive applications can disengage the PLL without turning it off. Applications that require the
PLL to wake the MCU from wait mode also can deselect the PLL output without turning off the PLL.
Freescale Semiconductor
These read/write bits control the hardware center-of-range linear multiplier L, which controls the
hardware center-of-range frequency f
4.5.1 PLL Control
(PCTL) is set. See
bits disables the PLL and clears the BCS bit in the PCTL. See
4.3.2.5 Special Programming Exceptions
Reset initializes the bits to $6 to give a default range multiply value of 6.
The multiplier select bits have built-in protection that prevents them from
being written when the PLL is on (PLLON = 1).
The VCO range select bits have built-in protection that prevents them from
being written when the PLL is on (PLLON = 1) and prevents selection of the
VCO clock as the source of the base clock (BCS = 1) if the VCO range
select bits are all clear.
The VCO range select bits must be programmed correctly. Incorrect
programming may result in failure of the PLL to achieve lock.
Software can select the CGMVCLK divided by two as the CGMOUT source
even if the PLL is not locked (LOCK = 0). Therefore, software should make
sure the PLL is locked before setting the BCS bit.
Register. VRS[7:4] cannot be written when the PLLON bit in the PLL control register
4.3.2.5 Special Programming
MC68HC908MR32 • MC68HC908MR16 Data Sheet, Rev. 6.1
VRS
. See
for more information.
NOTE
NOTE
NOTE
4.3.2.1 PLL
Exceptions. A value of $0 in the VCO range select
Circuits,
4.3.3 Base Clock Selector Circuit
4.3.2.4 Programming the PLL
Interrupts
and
and
69