C8051F060_07 SILABS [Silicon Laboratories], C8051F060_07 Datasheet - Page 320

• Manufacturer Part Number: C8051F060_07
• Description: Mixed Signal ISP Flash MCU Family
• Manufacturer: SILABS [Silicon Laboratories]

C8051F060/1/2/3/4/5/6/7
320
EXTEST provides access to both capture and update actions, while Sample only performs a capture.
24, 26, 28, 30, 32,
25, 27, 29, 31, 33,
40, 42, 44, 46, 48,
41, 43, 45, 47, 49,
56, 58, 60, 62, 64,
57, 59, 61, 63, 65,
74, 76, 78, 80, 82,
75, 77, 79, 81, 83,
86, 88, 90, 92, 94,
8, 10, 12, 14, 16,
9, 11, 13, 15, 17,
96, 98, 100
18, 20, 22
19, 21, 23
34, 36, 38
35, 37, 39
50, 52, 54
51, 53, 55
66, 68, 70
67, 69, 71
Bit
72
73
84
85
0
1
2
3
4
5
6
7
Table 26.2. Boundary Data Register Bit Definitions (C8051F061/3/5/7)
Action
Capture Not used
Update
Capture Not used
Update
Capture CAN RX Output Enable to pin
Update
Capture CAN RX Input from pin
Update
Capture CAN TX Output Enable to pin
Update
Capture CAN TX Input from pin
Update
Capture External Clock from XTAL1 pin
Update
Capture Weak Pullup Enable from MCU
Update
Capture P0.n output enable from MCU (e.g. Bit 8 = P0.0, Bit 10 = P0.1, etc.)
Update
Capture P0.n input from pin (e.g. Bit 9 = P0.0, Bit 11 = P0.1, etc.)
Update
Capture P1.n output enable from MCU (follows P0.n numbering scheme)
Update
Capture P1.n input from pin (follows P0.n numbering scheme)
Update
Capture P2.n output enable from MCU (follows P0.n numbering scheme)
Update
Capture P2.n input from pin (follows P0.n numbering scheme)
Update
Capture P3.n output enable from MCU (follows P0.n numbering scheme)
Update
Capture P3.n input from pin (follows P0.n numbering scheme)
Update
Capture Reset Enable from MCU
Update
Capture Reset Input from /RST pin
Update
Capture P5.0, P5.1, P5.2, P5.3, P5.5, P5.7 (respectively) output enable from
Update
Capture P5.0, P5.1, P5.2, P5.3, P5.5, P5.7 (respectively) input from pin†
Update
Capture P6.n output enable from MCU (follows P0.n numbering scheme)†
Update
Target
Not used
Not used
CAN RX Output Enable to pin
CAN RX Output to pin
CAN TX Output Enable to pin
CAN TX Output to pin
Not used
Weak Pullup Enable to Port Pins
P0.n output enable to pin (e.g. Bit 8 = P0.0oe, Bit 10 = P0.1oe, etc.)
P0.n output to pin (e.g. Bit 9 = P0.0, Bit 11 = P0.1, etc.)
P1.n output enable to pin (follows P0.n numbering scheme)
P1.n output to pin (follows P0.n numbering scheme)
P2.n output enable to pin (follows P0.n numbering scheme)
P2.n output to pin (follows P0.n numbering scheme)
P3.n output enable to pin (follows P0.n numbering scheme)
P3.n output to pin (follows P0.n numbering scheme)
Reset Enable to /RST pin
Not used
MCU†
P5.0, P5.1, P5.2, P5.3, P5.5, P5.7 (respectively) output enable to pin†
P5.0, P5.1, P5.2, P5.3, P5.5, P5.7 (respectively) output to pin†
P6.n output enable to pin (follows P0.n numbering scheme)†
Rev. 1.2