Z8F2480AN020SG Zilog, Z8F2480AN020SG Datasheet - Page 316

• Manufacturer Part Number: Z8F2480AN020SG
• Description: MCU 8BIT 24KB FLASH 44LQFP
• Manufacturer: Zilog
• Series: Encore!® XP®r

Specifications of Z8F2480AN020SG

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LED, LVD, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-LQFP
• Processor Series: Z8F248x
• Core: eZ8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 3
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: 770-1002 - ISP 4PORT ZILOG Z8 ENCORE! MCU269-4643 - KIT DEV Z8 ENCORE XP 28-PIN269-4630 - DEV KIT FOR Z8 ENCORE 8K/4K269-4629 - KIT DEV Z8 ENCORE XP 28-PIN269-4628 - KIT DEV Z8 ENCORE XP 8-PIN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4676

Table 166. OCD Line Control Register (OCDLCR)
BITS
FIELD
RESET
R/W
PS025011-1010
Line Control Register
7
The Line Control register is used to configure the output driver characteristics during
transmission. This register is only used in high-speed implementations.
NBTX—Nine Bit Transmit
This control bit sets the polarity of the ninth bit when nine bit mode is enabled.
0 = Ninth bit is zero.
1 = Ninth bit is one.
NBEN—Nine Bit Enable
This control bit enables nine bit mode. This is useful when transmit flow control using
remote start bit is enabled to detect valid characters.
0 = Nine Bit mode disabled.
1 = Nine Bit mode enabled.
TXFC—Transmit Flow Control
0 = Transmit Flow Control disabled.
1 = Transmit Flow Control using Remote Start bit.
TXDH — Transmit Drive High
0 = Pin is not driven high during 0 to 1 transitions.
1 = Pin is driven high during 0 to 1 transitions.
TXD—Transmit Drive
0 = Pin is only driven low during transmission (Open-Drain).
1 = Pin is always driven during transmission.
TXHD—Transmit High Drive Strength
0 = Pin output driver is low drive strength.
1 = Pin output driver is high drive strength.
Reset
00
R
6
NBTX
R/W
5
0
P R E L I M I N A R Y
NBEN
R/W
4
0
TXFC
R/W
3
0
Z8 Encore! XP
TXDH
R/W
2
0
Product Specification
TXD
R/W
1
0
®
On-Chip Debugger
F1680 Series
TXHD
R/W
0
0
302