UPD70F3765GF-GAT-AX Renesas Electronics America, UPD70F3765GF-GAT-AX Datasheet - Page 1308

• Manufacturer Part Number: UPD70F3765GF-GAT-AX
• Description: MCU 32BIT V850ES/JX3-H 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Hr

Specifications of UPD70F3765GF-GAT-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: CSI, EBI/EMI, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JG3-H, V850ES/JH3-H
25.2 Registers
R01UH0042EJ0400 Rev.4.00
Sep 30, 2010
(1) Power save control register (PSC)
The PSC register is an 8-bit register that controls the standby function. The STP bit of this register is used to
specify the standby mode. This register is a special register that can be written only by the special sequence
combinations (see 3.4.8 Special registers).
This register can be read or written in 8-bit or 1-bit units.
Reset sets this register to 00H.
Note Standby mode set by STP bit: IDLE1, IDLE2, STOP, or sub-IDLE mode
Cautions 1. Before setting the IDLE1, IDLE2, STOP, or sub-IDLE mode, set the PSMR.PSM1
After reset: 00H
PSC
NMI1M
NMI0M
INTM
STP
2. Settings of the NMI1M, NMI0M, and INTM bits are invalid when HALT mode is
3. If the NMI1M, NMI0M, or INTM bit is set to 1 at the same time the STP bit is set
0
1
0
1
0
1
0
1
0
and PSMR.PSM0 bits and then set the STP bit.
released.
to 1, the setting of NMI1M, NMI0M, or INTM bit becomes invalid. If there is an
unmasked
IDLE1/IDLE2/STOP mode is set, set the bit corresponding to the interrupt
request signal (NMI1M, NMI0M, or INTM) to 1, and then set the STP bit to 1.
Releasing standby mode by INTWDT2 signal enabled
Releasing standby mode by INTWDT2 signal disabled
Releasing standby mode by NMI pin input enabled
Releasing standby mode by NMI pin input disabled
Releasing standby mode by maskable interrupt request signals enabled
Releasing standby mode by maskable interrupt request signals disabled
Normal mode
Standby mode
NMI1M
R/W
Control of releasing standby mode by maskable interrupt request signals
< >
Control of releasing standby mode by INTWDT2 signal
interrupt
Address: FFFFF1FEH
Control of releasing standby mode by NMI pin input
NMI0M
< >
INTM
request
< >
Standby mode
signal
0
Note
setting
being
CHAPTER 25 STANDBY FUNCTION
0
held
STP
< >
pending
0
Page 1308 of 1509
when
the