MC9S12E64CFU Freescale Semiconductor, MC9S12E64CFU Datasheet - Page 516

• Manufacturer Part Number: MC9S12E64CFU
• Description: IC MCU 64K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E64CFU

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Data Bus Width: 16 bit
• Data Ram Size: 4 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 16 bit
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• On-chip Dac: 8 bit, 2 Channel
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

Chapter 18 Multiplexed External Bus Interface (MEBIV3)
18.2
In typical implementations, the MEBI sub-block of the core interfaces directly with external system pins.
Some pins may not be bonded out in all implementations.
Table 18-1
of these pins and associated pull-ups or pull-downs is dependent on the mode of operation and on the
integration of this block at the chip level (chip dependent).
516
BKGD/MODC/
TAGHI
PA7/A15/D15/D7
thru
PA0/A8/D8/D0
PB7/A7/D7
thru
PB0/A0/D0
PE7/NOACC
PE6/IPIPE1/
MODB/CLKTO
.
Pin Name
External Signal Description
outlines the pin names and functions and gives a brief description of their operation reset state
MODC
BKGD
TAGHI
PA7–PA0
A15–A8
D15–D8
D15/D7
thru
D8/D0
PB7–PB0
A7–A0
D7–D0
PE7
NOACC
MODB
PE6
IPIPE1
CLKTO
Pin Functions
Table 18-1. External System Pins Associated With MEBI
MC9S12E128 Data Sheet, Rev. 1.07
At the rising edge on RESET, the state of this pin is registered into the MODC
bit to set the mode. (This pin always has an internal pullup.)
Pseudo open-drain communication pin for the single-wire background debug
mode. There is an internal pull-up resistor on this pin.
When instruction tagging is on, a 0 at the falling edge of E tags the high half of
the instruction word being read into the instruction queue.
General-purpose I/O pins, see PORTA and DDRA registers.
High-order address lines multiplexed during ECLK low. Outputs except in
special peripheral mode where they are inputs from an external tester system.
High-order bidirectional data lines multiplexed during ECLK high in expanded
wide modes, special peripheral mode, and visible internal accesses (IVIS = 1)
in emulation expanded narrow mode. Direction of data transfer is generally
indicated by R/W.
Alternate high-order and low-order bytes of the bidirectional data lines
multiplexed during ECLK high in expanded narrow modes and narrow accesses
in wide modes. Direction of data transfer is generally indicated by R/W.
General-purpose I/O pins, see PORTB and DDRB registers.
Low-order address lines multiplexed during ECLK low. Outputs except in
special peripheral mode where they are inputs from an external tester system.
Low-order bidirectional data lines multiplexed during ECLK high in expanded
wide modes, special peripheral mode, and visible internal accesses (with
IVIS = 1) in emulation expanded narrow mode. Direction of data transfer is
generally indicated by R/W.
General-purpose I/O pin, see PORTE and DDRE registers.
CPU No Access output. Indicates whether the current cycle is a free cycle. Only
available in expanded modes.
At the rising edge of RESET, the state of this pin is registered into the MODB
bit to set the mode.
General-purpose I/O pin, see PORTE and DDRE registers.
Instruction pipe status bit 1, enabled by PIPOE bit in PEAR.
System clock test output. Only available in special modes. PIPOE = 1 overrides
this function. The enable for this function is in the clock module.
Description
Freescale Semiconductor