AT91SAM7X128 Atmel, AT91SAM7X128 Datasheet - Page 265

no-image

AT91SAM7X128

Manufacturer Part Number
AT91SAM7X128
Description
MCU 32-Bit 91S ARM7TDMI RISC 128KB Flash 1.8V/3.3V 100-Pin LQFP
Manufacturer
Atmel
Datasheet

Specifications of AT91SAM7X128

Package
100LQFP
Device Core
ARM7TDMI
Family Name
91S
Maximum Speed
55 MHz
Ram Size
32 KB
Program Memory Size
128 KB
Operating Supply Voltage
1.8|3.3 V
Data Bus Width
32 Bit
Program Memory Type
Flash
Number Of Programmable I/os
62
Interface Type
CAN/Ethernet/SPI/I2S/TWI/USART/USB
On-chip Adc
8-chx10-bit
Operating Temperature
-40 to 85 °C
Number Of Timers
3

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT91SAM7X128-AU
Manufacturer:
ATMEL
Quantity:
1 045
Part Number:
AT91SAM7X128-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT91SAM7X128-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT91SAM7X128-AU-999
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT91SAM7X128-CU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT91SAM7X128-CU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT91SAM7X128-CU-999
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT91SAM7X128B-AU
Manufacturer:
Atmel
Quantity:
1 929
Part Number:
AT91SAM7X128B-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT91SAM7X128B-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Figure 28-8. Peripheral Deselection
28.6.3.8
28.6.4
6120H–ATARM–17-Feb-09
Write SPI_TDR
Write SPI_TDR
Write SPI_TDR
NPCS[0..3]
NPCS[0..3]
NPCS[0..3]
TDRE
TDRE
TDRE
SPI Slave Mode
Mode Fault Detection
A
A
A
DLYBCT
DLYBCT
DLYBCT
Figure 28-8
A mode fault is detected when the SPI is programmed in Master Mode and a low level is driven
by an external master on the NPCS0/NSS signal. NPCS0, MOSI, MISO and SPCK must be con-
figured in open drain through the PIO controller, so that external pull up resistors are needed to
guarantee high level.
When a mode fault is detected, the MODF bit in the SPI_SR is set until the SPI_SR is read and
the SPI is automatically disabled until re-enabled by writing the SPIEN bit in the SPI_CR (Con-
trol Register) at 1.
By default, the Mode Fault detection circuitry is enabled. The user can disable Mode Fault
detection by setting the MODFDIS bit in the SPI Mode Register (SPI_MR).
When operating in Slave Mode, the SPI processes data bits on the clock provided on the SPI
clock pin (SPCK).
The SPI waits for NSS to go active before receiving the serial clock from an external master.
When NSS falls, the clock is validated on the serializer, which processes the number of bits
CSAAT = 0
DLYBCS
DLYBCS
DLYBCS
PCS = B
PCS=A
shows different peripheral deselection cases and the effect of the CSAAT bit.
PCS = A
A
AT91SAM7X512/256/128 Preliminary
B
A
A
A
A
DLYBCT
DLYBCT
DLYBCT
CSAAT = 1
DLYBCS
DLYBCS
PCS = B
PCS = A
A
A
PCS = A
DLYBCS
A
A
B
265

Related parts for AT91SAM7X128