PEB 4364 T V1.2 Infineon Technologies, PEB 4364 T V1.2 Datasheet - Page 75

no-image

PEB 4364 T V1.2

Manufacturer Part Number
PEB 4364 T V1.2
Description
IC SLIC VOICE ACCESS PDSO-36
Manufacturer
Infineon Technologies
Series
DuSLICr
Datasheet

Specifications of PEB 4364 T V1.2

Function
Dual Channel Subscriber Line Interface Circuit (DuSLIC)
Interface
IOM-2, PCM
Number Of Circuits
2
Voltage - Supply
3.3 V ~ 5 V
Current - Supply
105mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
36-PDSO
Includes
DTMF Generator and Decoder, Line Echo Cancellation (LEC), Teletax (TTX) Generation, Universal Tone Detection (UTD)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power (watts)
-
Other names
PEB4364TV1.2XT
SP000007728
Table 13
SLICOFI-2x
Mode
Active with
Metering
Ground Start
Ring Pause
1) CIDD = Data Downstream Command/Indication Channel Byte (IOM-2 Interface)
2) If not otherwise stated in the table, the bits ACTL, ACTR, HIT, HIR must be set to 0.
3) Only for SLIC-S
4) HIT = High Impedance on Tip
5) HIR = High Impedance on Ring
6) ACTx means ACTH, ACTL or ACTR.
Sleep (SL) – only available with DuSLIC-E/-E2/-P/-ES/-ES2
The SLICOFI-2 is able to go into Sleep mode with minimal power dissipation. In this
mode, off-hook detection is performed without any checks on spikes or glitches. The
Sleep mode can be used for either channel, but for the most effective power savings,
both channels should be set to this mode. Note that this requires the following:
Preliminary Data Sheet
CIOP = Command/Indication Operation
For further information, see
If both channels are set to the Sleep mode, only non-noisy lines should be used due
to the lack of persistence checking. Wake up takes about 1.25 ms, as the on-chip
PLL is also switched off. Therefore, it is also possible to switch off all external clocks.
In this mode, no programming or other functionality is available. The off-hook event
is indicated either by (1) setting the interrupt pin to Low level, if the PCM/ C Interface
mode is selected, or (2) pulling down the DU pin, if IOM-2 Interface is used.
If only one channel is set to Sleep mode, persistence checking and off-hook
indication are performed as in any other mode, but the off-hook level is fixed to 2 mA
at the subscriber line. No special wake up is needed if only one channel is in Sleep
mode. A simple mode change ends the Sleep mode.
A sleeping SLICOFI-2 wakes up if the CS pin is drawn to low level when the PCM/ C
Interface is used or if the MX bit is set to 0 when the IOM-2 Interface is used. Note
Overview of all DuSLIC Operating Modes (cont’d)
SLIC-S/
SLIC-S2
ACTx
HIT
ACTR
3) 6)
“SLICOFI-2x Command Structure and Programming” on Page
3)
SLIC Type
SLIC-E/
SLIC-E2
ACTx
HIT
ACTR
4)
SLIC-P M2 M1 M0
ACTx
HIT
ACTR
ROR
ROT
75
4)
CIDD/CIOP
1
1
1
0
1
0
0
0
1)
0
0
0
1
Additional Bits used
TTX-DIS to select Reverse
Polarity or TTX Metering
ACTR = 0
HIR = 1
HIT = 1
Operational Description
DS3, 2003-07-11
140.
DuSLIC
2)

Related parts for PEB 4364 T V1.2