MT29C4G48MAZAPAKD-5 E IT Micron, MT29C4G48MAZAPAKD-5 E IT Datasheet - Page 60
MT29C4G48MAZAPAKD-5 E IT
Manufacturer Part Number
MT29C4G48MAZAPAKD-5 E IT
Description
Manufacturer
Micron
Datasheet
1.MT29C4G48MAZAPAKD-5_IT.pdf
(218 pages)
- Current page: 60 of 218
- Download datasheet (5Mb)
Column Address Operations
RANDOM DATA READ (05h-E0h)
Figure 35: RANDOM DATA READ (05h-E0h) Operation
PDF: 09005aef83ba4387
168ball_nand_lpddr_j42p_j4z2_j4z3_omap.pdf – Rev. H 3/11
Cycle type
I/O[7:0]
SR[6]
D
Dn
OUT
Dn + 1
D
The column address operations affect how data is input to and output from the cache
registers within the selected die (LUNs). These features provide host flexibility for man-
aging data, especially when the host internal buffer is smaller than the number of data
bytes or words in the cache register.
When the asynchronous interface is active, column address operations can address any
byte in the selected cache register.
The RANDOM DATA READ (05h-E0h) command changes the column address of the se-
lected cache register and enables data output from the last selected die (LUN). This
command is accepted by the selected die (LUN) when it is ready (RDY = 1; ARDY = 1). It
is also accepted by the selected die (LUN) during CACHE READ operations
(RDY = 1; ARDY = 0).
Writing 05h to the command register, followed by two column address cycles contain-
ing the column address, followed by the E0h command, puts the selected die (LUN)
into data output mode. After the E0h command cycle is issued, the host must wait at
least
mode until another valid command is issued.
In devices with more than one die (LUN) per target, during and following interleaved
die (multi-LUN) operations, the READ STATUS ENHANCED (78h) command must be
issued prior to issuing the RANDOM DATA READ (05h-E0h). In this situation, using the
RANDOM DATA READ (05h-E0h) command without the READ STATUS ENHANCED
(78h) command will result in bus contention because two or more die (LUNs) could
output data.
OUT
t
WHR before requesting data output. The selected die (LUN) stays in data output
t
RHW
Command
05h
168-Ball NAND Flash and LPDDR PoP (TI OMAP) MCP
Address
C1
60
Address
C2
Command
Micron Technology, Inc. reserves the right to change products or specifications without notice.
E0h
t
Column Address Operations
WHR
D
Dk
© 2009 Micron Technology, Inc. All rights reserved.
OUT
Dk + 1
D
OUT
Dk + 2
D
OUT
Related parts for MT29C4G48MAZAPAKD-5 E IT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
VFBGA 63/I°//MICRON NAND FLASH 1Gb Mass Storage
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
SYNCHRONOUS DRAM
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Q-FLASHTM MEMORY
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
4Meg x 4, 3,3V FPM DRAM
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
4Meg x 4, 3,3V FPM DRAM
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
4Meg x 4 banks, EDO DRAM, 3.3V, standard refresh, 50ns
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
4Meg x 4 banks, EDO DRAM, 3.3V, standard refresh, 50ns
Manufacturer:
Micron Semiconductor Products
Datasheet:
Part Number:
Description:
4Meg x 4 banks, EDO DRAM, 3.3V, standard refresh, 60ns
Manufacturer:
Micron Semiconductor Products
Datasheet: