C8051F226DK Silicon Laboratories Inc, C8051F226DK Datasheet - Page 125

• Manufacturer Part Number: C8051F226DK
• Description: DEV KIT F220/221/226/230/231/236
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F226DK

• Contents: Evaluation Board, Power Supply, USB Cables, Adapter and Documentation
• Processor To Be Evaluated: C8051F22x and C8051F23x
• Interface Type: USB
• Silicon Manufacturer: Silicon Labs
• Core Architecture: 8051
• Silicon Core Number: C8051F226
• Silicon Family Name: C8051F2xx
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With/related Products: C8051F220, 221, 226, 230, 231, 236
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1241

17. Timers
The CIP-51 implements three, 16-bit counter/timers comparable with those found in the standard 8051
MCU's. These can be used to measure time intervals, count external events and generate periodic inter-
rupt requests. Timer 0 and Timer 1 are nearly identical and have four primary modes of operation. Timer
2 offers additional capabilities not available in Timers 0 and 1, such as capture and baud rate generation.
When functioning as a timer, the counter/timer registers are incremented on each clock tick. Clock ticks
are derived from the system clock divided by either one or twelve as specified by the Timer Clock Select
bits (T2M–T0M) in CKCON. The twelve-clocks-per-tick option provides compatibility with the older gener-
ation of the 8051 family. Applications that require a faster timer can use the one-clock-per-tick option.
When functioning as a counter, a counter/timer register is incremented on each high-to-low transition at the
selected input pin (P0.4/T0, P0.5/T1, or P0.6/T2. Events with a frequency of up to one-fourth the system
clock's frequency can be counted. The input signal need not be periodic, but it should be held at a given
level for at least two full system clock cycles to ensure the level is sampled.
17.1. Timer 0 and Timer 1
Timer 0 and Timer 1 are accessed and controlled through SFR's. Each counter/timer is implemented as a
16-bit register accessed as two separate bytes: a low byte (TL0 or TL1) and a high byte (TH0 or TH1). The
Counter/Timer Control (TCON) register is used to enable Timer 0 and Timer 1 as well as indicate their sta-
tus. Both counter/timers operate in one of four primary modes selected by setting the Mode Select bits
M1–M0 in the Counter/Timer Mode (TMOD) register. Each timer can be configured independently. Follow-
ing is a detailed description of each operating mode.
17.1.1. Mode 0: 13-bit Counter/Timer
Timer 0 and Timer 1 operate as a 13-bit counter/timer in Mode 0. The following describes the configuration
and operation of Timer 0. However, both timers operate identically and Timer 1 is configured in the same
manner as described for Timer 0.
The TH0 register holds the eight MSB's of the 13-bit counter/timer. TL0 holds the five LSBs in bit positions
TL0.4–TL0.0. The three upper bits of TL0 (TL0.7–TL0.5) are indeterminate and should be masked out or
ignored when reading. As the 13-bit timer register increments and overflows from 0x1FFF (all ones) to
0x0000, the timer overflow flag TF0 (TCON.5) is set and an interrupt will occur if enabled.
The C/T0 bit (TMOD.2) selects the counter/timer's clock source. Clearing C/T selects the system clock as
the input for the timer. When C/T0 is set to logic 1, high-to-low transitions at the selected input pin incre-
ment the timer register. (Refer to section 14 for information on selecting and configuring external I/O pins.)
Setting the TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is 0 or the input signal /INT0
is logic-level one. Setting GATE0 to logic 1 allows the timer to be controlled by the external input signal
/INT0, facilitating pulse width measurements.
13-bit counter/timer
16-bit counter/timer
8-bit counter/timer with auto-reload
Two 8-bit counter/timers (Timer 0 only)
Timer 0 and Timer 1:
Rev. 1.6
16-bit counter/timer with auto-reload
16-bit counter/timer with capture
Baud rate generator
Timer 2:
C8051F2xx
125