EVB9S08DZ60 Freescale Semiconductor, EVB9S08DZ60 Datasheet - Page 253

• Manufacturer Part Number: EVB9S08DZ60
• Description: BOARD EVAL FOR 9S08DZ60
• Manufacturer: Freescale Semiconductor
• Type: MCUr

Specifications of EVB9S08DZ60

• Contents: Module and Misc Hardware
• Processor To Be Evaluated: S08D
• Data Bus Width: 8 bit
• Interface Type: RS-232, USB
• Silicon Manufacturer: Freescale
• Core Architecture: HCS08
• Core Sub-architecture: HCS08
• Silicon Core Number: MC9S08
• Silicon Family Name: S08D
• Kit Contents: Board Cables CD Power Supply
• Rohs Compliant: Yes
• For Use With/related Products: MC9S08DZ60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MSCAN then schedules the message for transmission and signals the successful transmission of the
buffer by setting the associated TXE flag. A transmit interrupt (see
is generated
If more than one buffer is scheduled for transmission when the CAN bus becomes available for arbitration,
the MSCAN uses the local priority setting of the three buffers to determine the prioritization. For this
purpose, every transmit buffer has an 8-bit local priority field (PRIO). The application software programs
this field when the message is set up. The local priority reflects the priority of this particular message
relative to the set of messages being transmitted from this node. The lowest binary value of the PRIO field
is defined to be the highest priority. The internal scheduling process takes place whenever the MSCAN
arbitrates for the CAN bus. This is also the case after the occurrence of a transmission error.
When a high priority message is scheduled by the application software, it may become necessary to abort
a lower priority message in one of the three transmit buffers. Because messages that are already in
transmission cannot be aborted, the user must request the abort by setting the corresponding abort request
bit (ABTRQ) (see
(CANTARQ)”.) The MSCAN then grants the request, if possible, by:
12.5.2.3
The received messages are stored in a five stage input FIFO. The five message buffers are alternately
mapped into a single memory area (see
exclusively associated with the MSCAN, but the foreground receive buffer (RxFG) is addressable by the
CPU (see
applicable for the receive process.
All receive buffers have a size of 15 bytes to store the CAN control bits, the identifier (standard or
extended), the data contents, and a time stamp, if enabled (see
Message
The receiver full flag (RXF) (see
signals the status of the foreground receive buffer. When the buffer contains a correctly received message
with a matching identifier, this flag is set.
On reception, each message is checked to see whether it passes the filter (see
Acceptance
valid message, the MSCAN shifts the content of RxBG into the receiver FIFO
generates a receive interrupt (see
handler must read the received message from the RxFG and then reset the RXF flag to acknowledge the
interrupt and to release the foreground buffer. A new message, which can follow immediately after the IFS
1. The transmit interrupt occurs only if not masked. A polling scheme can be applied on TXEx also.
2. Only if the RXF flag is not set.
3. The receive interrupt occurs only if not masked. A polling scheme can be applied on RXF also.
Freescale Semiconductor
1. Setting the corresponding abort acknowledge flag (ABTAK) in the CANTAAK register.
2. Setting the associated TXE flag to release the buffer.
3. Generating a transmit interrupt. The transmit interrupt handler software can determine from the
setting of the ABTAK flag whether the message was aborted (ABTAK = 1) or sent (ABTAK = 0).
Storage”).
Figure
1
Filter”) and simultaneously is written into the active RxBG. After successful reception of a
Receive Structures
when TXEx is set and can be used to drive the application software to re-load the buffer.
12-38). This scheme simplifies the handler software because only one address area is
Section 12.3.8, “MSCAN Transmitter Message Abort Request Register
Section 12.3.4.1, “MSCAN Receiver Flag Register
Section 12.5.7.3, “Receive
MC9S08DZ60 Series Data Sheet, Rev. 4
Figure
12-38). The background receive buffer (RxBG) is
Chapter 12 Freescale’s Controller Area Network (S08MSCANV1)
Interrupt”) to the CPU
Section 12.4, “Programmer’s Model of
Section 12.5.7.2, “Transmit
Section 12.5.3, “Identifier
2
, sets the RXF flag, and
3
. The user’s receive
(CANRFLG)”)
Interrupt”)
253